nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I've seen many posts about LL_LENGTH_REQ causing disconnection on certain Android phones and the solution from Nordic is to add a 100ms delay. Can someone from Nordic definitively...
Hi community,
in our setup we use the LSM6DSL IMU using TWI. First we initialize the TWI peripheral, then we configure the IMU. After that we initialize PPI to automatically...
I am trying to build the project "thingysdkv210" which is downloaded from https://www.nordicsemi.com/Software-and-tools/Prototyping-platforms/Nordic-Thingy-52/Download#infotabs...
nRF52 DK
HTS example
I added app_timer_stop_all() in the ble_evt_handler() of main.c, under the case of BLE_GAP_EVT_DISCONNECTED, but the battery service timer still...
need help on multiple things
All work is on the DK 840 board using sdk15.3
Started with this link
https://rigado.zendesk.com/hc/en-us/articles/360025376053-Add-Nordic...
Is it possible to run the Zigbee Light Switch example with the internal RC.?
On the sdk_config.h I have changed the following:
#define NRFX_CLOCK_CONFIG_LF_SRC 0
But...
In the only example in SDK16.0.0 with soft_device and Free RTOS, configMAX_PRIORITIES is set to 3, which means available priorities 0,1 and 2.
Is it possible to change configMAX_PRIORITIES...
Hi i'm very new in using Nordic nRF52840. Got 2 questions:
1.Why does each example project contain blank/mbr/slxxx folders? in these folders they all have a copy of the...
Hi,
we've been experiencing some strange issues with the OTA DFU on nRF Connect for Androind in the past two days.
We've been using such function on a regular basis with...
I am trying to transition my Nordic SDK v12 project from Keil to Segger Embedded studio. I followed the tutorial steps such as placing ses_nrf_51_startup.s file in Internal...
Can I use an external edge-triggered (negative edge) interrupt (on a GPIO pin) to trigger an I2C write via PPI? If so, do the I2C registers need to be reloaded each time?...
I'm having trouble using an external j-link probe (J-Link plus compact) with the nRF52840-DK with Segger Embedded Studio. I am powering the DK from USB (Sw9 VDD) , using the...
Hi Great QA team:
Our clients are studying for the details of 52833. And they'd like to know the maximum external draw current through VDD at high voltage mode.
It's clearly...
Hi,
I am testing the ble blinky example as it is from SDK v16.0.0. I am seeing a good amount of time(~340ms) from reset(pin reset) to advertise the first packet. I am keen...
