after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I'm compiliing against version 1.1.0 of the ncs, and my device have the mfw 1.1.0 firmware running.
When starting the device, I get the following output:
This is not...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
I am new to DFU feature on Nordic. I have...
I have custom board with nrf 52832. I am using SDK 15.2.0. and soft devices s132 V6.1.0 to transmit advertising packets with advertising interval 1s. I have written simple...
Hello :)
After upgrading the modem firmware of the nRF9160 to version 1.1.0 (mfw_nrf9160_1.1.0.zip) the call to getaddrinfo returns error 12.
If I downgrade to version...
Hello, everyone~
A new requirement is generated from my customer. He wants the ANCS can transmit more than 20m in a house. So I want to know if BLE 5.0 long range can transmit...
Hello!
I am dealing with nrf52832. I want to process data reception with SPI during f_write processing. Is this possible? As multi-thread processing 1) PT_THREAD in pt...
I'm developing a wearable device using nRF52832. I am developing OTA-DFU nowadays. I have successfully tested the buttonless OTA-DFU using the nRF52-DK.
And I'm testing...
Hi, I have a nRF9160 and I am currently working with the gps example: ncs\nrf\samples\nrf9160\gps
When I run the example, I only see
all the time. I went out on a big...
Hello,
i am struggling with the implementation of i2s to use it one SK6812 Leds.
To start with i used this https://github.com/cheehieu/nrf52-sk6812-led-driver example...
Hi All,
I study this post to enable long-range(s=8) on ble_app_blinky ( nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral\ble_app_blinky )
In the post, one of the settings...
Hello,
I was able to program the mesh experimental dimming example(server) into the external nRF52832 module using the debug out pins on the nRF52 DK.
The programming...
Hi,, I'm trying to set a recv timeout on a UDP socket (coap) using setsockopt() and getting an EPERM error. I've tried the setsockopt() call both before and after the (successful...
I'm attempting to use AWS IoT Just In TIme Provisioning(JITP), but no luck. Any help.
I tested JITP on my account, not Nordic one, with local mosuqitto client on Mac and...
I'm trying to use aws_fota, but it doesn't work. Any help?
I was able to set a job on AWS IoT, but the download job doesn't start. The job status is always "in progress...
