Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I am a hardware and software embedded developer. I used to SKY369 based on NRF52832 in our bluetooth project, i use softdevice S132 firmware. I can programming with...
Hi All.
SDK15.3.0 / DK / nRF52840
I've been testing DFU on nRF52840 with DK.
When i tested it on nRF52832 all works fine. i followed this ( https://devzone.nordicsemi...
Hi,
Is anybody tried to implement GPFS on NRF52? https://developers.google.com/nearby/fast-pair/spec In general, everything looks clear, but want to save time on development...
Hi,
After adding ANCS client service to my firmware, firmware crashed.
Investing I could see it was failing to allocate memory
File: task.c
Line no: 2012
else...
HI ALL
I am using SDK15.3.0 to familiarize myself with GPIOTE functions,But I have encountered some problems.
First ,I registered 4 GPIOTE pins on the DK board,and I need...
Hello!
As the title suggests, I want to know how to use DMA with fatfs. It is defined like this, but now is fatfs using DMA?
It takes 18ms to write 512 bytes with f_write...
Hello,
I will use the I2S driver instead the direct acess to the registers.
I have implemented the registers version like this and it works / sounds normaly.
now I...
I am not able to create my new User account in nRF Cloud and I can not test my Thingy 91. I tried Google Chrome and IE but both Browsers did not work. I tried my iPhone Safari...
I did a chip-erase on the NRF51 DK. However, when I tried to reconnect and program the DK I get the error: Failed to connect to target, no Idcode detected
I tried doing...
Hello,
At the following line
I get the error:
hal.c(35): error: #20: identifier "NRF_DRV_TWI_INSTANCE_0" is undefined
When looking further it seems likein the...
I have custom board with nrf 52832. I am using SDK 15.2.0 and softdevice s132 V6.1.0 to transmit advertising packets periodically. I have written simple application that reads...
Hi Everyone,
I’ve implemented a ST7735S on the NRF52832 using the GFX example. My problem is that I can’t seem to update the screen in such a way that the screen doesn’t...
Hello,
I am trying to make LSM6DSR (STEVAL-MKI194V1) work with nRF52840 using TWI Communication.
Problem:
Firstly, I modified the TWI sensor example to use the accelerometer...
Hi guys, I've got a nRF 52840-DK, I want to verify the new features like 2M/long range/advertising extension.
1. Is there any exmaple to test these featues, or any guideline...
