Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi,
I would like to debug the code which is in Nordic Thingy91 by using nRF52840DK.
Is it possible to use the debugger in nRF52840DK for Nordic Thingy91 ?
If it is possible...
Hi,
I like to understand what SBs should I cut, what switched should I use to measure the SOC current only with PCA10056 board. I use the Otii Arc device to supply power...
Hello,
I'm working on NRF52832 based module BMD-301
for same i'm using SDK16 Segger Embedded Studio
The thing is
when uploaded ble_app_alert_notification example it...
Hello,
I've tried to convert the mesh light switch server example from NRF52840 DK to Dongle following this post.
Unfortunately that doesn't work.
I've changed the BOARD_PCA10056...
Currently, there is a project. The situation is that the master nRF52840 communicates with the cloud server through the GPRS232 module, the slave nRF52840 communicates with...
Hi,
I tried to create a custom server in using server setup of nRF Connect v3.3.0 but when I tried to apply my custom server on my device, the software bugs instantly. ...
I want to modfiy the code in the example ble_app_ancs_c to read the internal flash with fstorage. But after I set APP_TIMER_CONFIG_USE_SCHEDULER to 1, the operation of fstorage...
Hi every one, I am running light switch example (using SDK 15.2 and SDK for Mesh version 3.1.0 ). The problem is: My provisioner node cannot Receive RSSI message of a node...
I am trying to save and read a structure using FDS, how do I go about it?
I have the structure:
My custom function for saving is:
I call the function using below...
This error always stop the "mqtt_simple" application.
I have tried modem versions 1.0.1 and 1.1.0, SDK versions v1.0.0 and v1.1.0 and added this code to system_nrf9160.c...
I have an Android application running with RxAndroidBle library and I want to change it to Nordic-Ble-Android library. I'm not that good with Bluetooth and the actual version...
Hello, i'm new in BLE and i would like to know, what is the best way to read and write 200-300 parameters of my product via BLE from a phone?
Possibility 1 is, to create...
I am trying to save and read a structure using FDS, how do I go about it?
I have the structure:
Is this correct by populating the record as such?:
And to read...
Hello,
is there any tutorial on how to send commands to the Thingy52 from an Android app (like the Thingy52 app or nRF Connect) to start the RTC clock (and then read/clear...
My 52833DK is apparently bricked. I get the message "Could not find core in Coresight setup. Abort debug session” When I try to load code (IAR) into the board. It was working...
