Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hi,
Please help to share Memory size of following SoftDevices:
S112
S113
S132
S140
Also, what will be the memory size of SoftDevice if i implement Central +...
Hi,
We are migrating from 12.3 SDK version to 15.3 version.
We observed the almost 22 KB of RAM is reserved. Where as in 12.3SD version we don't see this.
We are still...
Hi,
our company one new product using you nRF52832. We already prepared everything for CE (RED ) and FCC certification process. Only thing that is unclear is Bluetooth SIG...
Hi!
I am currently using SEGGER Embedded Studio version 4.12, nRF5 SDK version 15.2.0, nRF5 SDK for Mesh version 3.1.0, Hardware BMD-300 Evaluation Board.
i using the...
I need to measure a load-cell bridge. Although, I'm fairly certain I'd be better off with an external delta-sigma ADC with an internal amplifier - I'd like to run through...
Hi,
I study on Thread resently.
I found it is not any output in the Debug Terminal Window when using NRF_LOG_XXX, but the J-link Control panel showed the logs.
Here...
Hi,
I am trying USB DFU trigger.
I have connected GPIO P024 to Reset port P018.
Bootloader is also programmed.
When I use nRF connect/programmer.
It's always waiting...
My system: MacBook Air with macOS 10.14.6, Xcode 10.3, with sdk at /Applications/Xcode.app/Contents/Developer/Platforms/MacOSX.platform/Developer/SDKs/MacOSX10.14.sdk
When...
Dear nRF52832 experts,
I have a SPI slave device which can periodically notify the MCU with data ready (DRDY) signal. For each DRDY signal, we should perform a SPI transaction...
Hi there, I am developing a mobile solution using BLE. Actually I use a sniffer based in IC nRF51822 and Wireshark + nrf sniffer as a tool for traffic capture. Sometimes,...
Hi,
I have similar problem to what is described here .
My situation: 1. I connect 2 PDM mics to the board (CLK is pin 27, Din is pin 26). 2. I connect a couple of TWI...
I was wondering if there is any way to setup a callback when data is received on an open socket, as opposed to just regularly polling the socket?
The application I have...