Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
Hi,
I'm trying to add the NUS service to an existing application (freertos based, SDK15.2, already use a custom service)
I copied the relevant code snippets from...
Hi everyone,
I'm trying to use nRF52810 with SoftDevice S112 to sample five ADC channels. I'm finding this very weird issue, where first channel is showing correct value...
Just getting started with Nordic toolchain and I got this error below.
=== updating civetweb (modules\lib\civetweb): --- civetweb: cloning and initializing Initialized...
i need a code for when button press after one second delay led will glow continiously whenever again pressing the switch it will stop glowing using apptimer
Hi, Everyone
My development environment is sdk15.3, nRF52840, Keil complier
The link error file is attached below.
Also I am going to use AES-CBC method.
Which example...
I'm experimenting with the USB MSC example (SDK 15.3) on my nRF52840 DK. It seems to work well in the polling mode as delivered. However, when I try to run in interrupt mode...
I have a serial port set upp with the serial port library like this:
#define UART_PIN_DISCONNECTED 0xFFFFFFFF /**< Value indicating that no pin is connected to this UART...
Hello,
I am trying to get started with the 9160-DK. So far it does not seem similar to the 52840 so I decided to take to the "Getting Started Assistant" within nRF Connect...
Hi, I'm using nrf52832 and SDK15.3. And I'm using the ble_app_uart example. The device will go to sleep mode if there is no connection for 3 mins.
My questions are:
1...
I'm calling sd_ble_gap_adv_start after a connection disconnects to start advertising again and it's returning err_code 12... which is NRF_ERROR_DATA_SIZE. However, the documentation...
Hello,
I am currently working on a project that involves the host device to send configurations parameters over to the device. I was hoping the connection between in device...
Hello All,
We working on OTA features with nRF52810 using sdk16.0 . When we are trying to upload the firmware zip format through mobile its giving error "upload failed:Insufficient...
Hi,
I am new at mesh .I use SDK UART coexistence example to test, and I can scan Ble uart demo by nrf Connect APP. But I can't scan Mesh node by nrf Mesh APP. I've been...
I am trying to program the Nordic nRF51822 MDBT40 Series module to communicate to an STM32 processor chip. The way I understand the procedure is as follows:
First, I must...
