Hello,
In ncs, I am working with \nrf\samples\ipc\ipc_service. I want MCUboot to build \nrf\samples\ipc\ipc_service\remote to run on nrf5340 CPUNET. When I CONFIG_BOARD_ENABLE_CPUNET...
Hi,
I am currently conducting measurements using channel sounding with my nRF54L15 boards. I am at the end of my master thesis, so there is not so much time left to really...
The nrfx pwm supports a number of events for a callback: /** @brief PWM driver event type. */ typedef enum { NRFX_PWM_EVT_FINISHED, ///< Sequence playback finished. NRFX_PWM_EVT_END_SEQ0...
Hi,
I have two nRF5340 DKs and want one to be server, one be client. I use NCS offcial code and simply buide them, however, " LED3 starts blinking green on every device...
Hello,
I have been working with the nRF9160 DK to understand AT commands. I tried flashing the Serial LTE Modem application using the Quick Start option in the nRF Connect...
Hi everyone,
In nRF9160 with ncs 2.9.0 I've problems when trying publish a MQTT payload bigger than 2700 bytes aproximately. In advanced I already was adequated buffer size...
I'm using the PCA10028, ble_app_hrs_dfu(sdk11).
Only the three screens below were repeated infinitely when I started to upgrade the softdevice through DFU.
And the...
My android version is the Kitkat.
The nRF Toolbox cannot find services when I changed the application of PCA10028 for example from ble_app_hts to ble_app_hrs.
The message...
Hi I am developing an application for sending data over BLE which I have received over SPI from a non - Nordic chip. I am using the ble_app_uart template for this. But data...
My call to sd_ble_gap_ppcp_set is returning NRF_ERROR_INVALID_PARAMETER.
I have the following connection interval settings:
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(500...
I am running SDK12.3 on an nRF52 and the bootloader on my boards has no problem replacing the application through the DFU process. Now I found a mistake in the bootloader...
I am not sure whether there is a small error in a Gazell packet transaction diagram, or if I have an incorrect understanding. From Gazell user guide :
If only the ACK...
Hi,
I am trying to achieve the maximum throughput when using the nRF51822.As far as I know, the minimum connection interval is 7.5ms and the maximum packets per interval...
I'm running the app_uart_c example on a nRF52832 with softdevice 132 installed.
I'm trying to alter it so that the board only searches for peripheral devices upon a button...
First time using the sniffer.
I want to sniff out the communication for a laser tape measuring device (Boosch GLM 50C)
I noticed that I am unable to sniff out anything...
Hello, I now is in a problem.My equipment set up matching binding but after binding equipment connection will connection failure.If it is not binding, it can be the connection...
Hi
We have developed the product where we are using the nrf51822 chip. Because we are using custom made PCB we have to make tunning of antenna for a long range of BLE module...
Hi All,
I am working on nrf52840 pdk, where i can see that my OLED SPI 128x32 display isn't displaying properly and displaying only garbage value.
Although the same...
I'm starting a new project using Nordic's nRF52840, I have the Preview-DK. My development environment is a MacBook Pro Running Parallels running windows 10. I have downloaded...
Hi, All!
I'm using nRF51822 to support custom protocol, and define array "packet[40]" for PACKETPTR. when "packet" is constant value, the radio tx is very stable; but when...
