Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I want to generate an interrupt event use pin30 when it goes from low->high or high->low.
First I register a gpiote user by
app_gpiote_user_params_t app_gpiote_params...
I found out answers for calculating data rate during connections, which depends upon connection interval, no of packets allowed in each connection and no of bytes in a single...
I am trying to stop RTC by pressing one button and wake up again by releasing the same button.
My RTC now runs around 4 uA while being on system-on sleep mode by __SEV();...
Hi,
I managed to get dfu working in application (with hrs). But on the last attempt to erase page with bootloader settings there is no event generated from softdevice and...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
I would like to know how frequently my peripheral is sending advertising and data packets. I've tried using ble-sniffer-osx but it doesn't actually reveal any device names...
Has anyone successfully used the Android-Beacon Library to detect the nRF51822 Beacon on and Android application? I tried several different layouts but I just can't detect...
Hi everyone;
i think about possibility of using nrf sniffer with custom nrf51822 (QFAA) board . if yes, how can i achieve? could you please help me about it
Best Re...
Hi All,
This is my first time i am designing a PCB for nrf52840, I need a suggestion regarding the antenna to be used. I am going to have an application over BLE. Which...
I want to add a timeout to the secure DFU bootloader if I enter it from the application. I found this post here devzone.nordicsemi.com/.../ but unfortuately I can't use the...
Hi I'm looking forward to hear if I could program an nRf51822 QFAA without using the development kit/board. The chip I have currently is a N51822- S4AT, from Wireless Tag...
we are facing problem with smt M905 module. is there any basic error with this module pad?
smt factory in china failed several times to solder this module.
Hi - In my app, I'm using Bluetooth, the ADC, the TWI, and the SPI. The general idea is to measure lots of things, store the data in SPI NOR FLASH, and occasionally flush...
I'm testing a custom application with the following configuration:
Custom app based on the ble_app_pwr_profiling SDK example.
Using SDK 13.1
S140 SoftDevice s140_nrf52840_5...
