Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
As a central, I am writing to a variable length characteristic, advertised by a service of my peripheral. In this case, I am sending 80 bytes of 0x01 as a test
uint8_t...
I used the ANCS program in sdk12.3.0, I have closed the white list function, I use the iphone connection and paired, then I ignore this device on the phone, and then I use...
Hi
I am using nrf51-dk board along with the S130. I am getting the following message when I debug my code. The central link count is set to 0 while peripheral link count...
Hello,
I didn't find much information about how different settings for the MTU size behaves with older versions of BLE devices. I'm using the softdevice s132 4.0.2.
...
When trying out the ble_app_hrs_freertos example in nRF5 SDK 11.0.0-2.alpha_bc3f6a0 , I seem to only get 14-character long device name announcements.
This happens when...
To @Hung Bui. Hello sir. I am new to NRF51 microcontrolers and I am trying to use Pstorage in my written code. I have noticed this post of your's:
I am using nrf51422...
Why do I call this bluetooth send function (ble_nus_string_send )return values is 04 not 00(return sd_ble_gatts_hvx), why will appear this kind of circumstance?When I send...
I am using nRF Connect with nRF52 and need to use UART over BLE to send command to the device but I find that you can only use hexadecimal input and get hexadecimal output...
I have nRF52 and working with SDK11.
I can start BLE advertising and nRF Connect app will detect everything correctly.
I only have an issue: I want to advertise for...
Hi there,
I am getting some error in my SAADC measurements and I believe it's due to the R_INPUT forming a parallel resistance with my voltage divider at the input (the...
Hi,
I am measuring the current during sleep, after the sequence, __WFE();__SEV();__WFE();.
With NRF_LOG_ENABLED set to 1, the current is about 486 uA. With NRF_LOG_ENABLED...
Using: nrf51822, SDK 10.
My application needs to use TWI0 and SPIS1 at the same time. However if I enable TWI0 and then SPIS1, when I run nrf_drv_spis_init() I get NRF_ERROR_INVALID_STATE...
