Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
I am mobile developer and very new to mcu programming. Due to our new product's requirements, I have to write program with new bluetooth chip. So if nrf51 and nrf52 series...
To find a clean channel for 2.4g Band to avoid the wifi channel, nRF24L01p would sweep frequency for all the channel (2400M~2525M). But looks like nRF24L01p not support to...
Hello guys!
I'm trying to port the TSS service to one of my projects.
This project is based on SDK13.1 while the Thingy is on SDK12.1
I have a lot of problems with...
Hello guys!
I'm trying to get softblinking led work with a SDK14.
The code works perfectly fine in one of my projects that use scheduler and SDK13.
But in SDK14, (only...
Hi, I think the idea of limiting the behavior of a model to states is very wise, but due to my limited understanding in this matter, I find it puzzling as to what happens...
Is it possible to use the NRF52832 UART in half-duplex single-wire mode, by assigning TXD and RXD to the same GPIO, setting the GPIO drive to disconnect '1' and using a pull...
I am running the example under peripheral\pwm_driver on PCA10040, and SDK 12.2.0. Using a scope, I measured the period (from rising edge to rising edge) on one of the LEDs...
In my project, the softdevice I used was S110
I hope that some of the data can still be retained after OTA updates,
in the Bootloader program code:
#define DFU_APP_DATA_RESERVED...
Hey togehter,
has anyone succeeded setting up a connection between ST-Link and nRF52832?
I connected the pins (GND, SWDIO, SWCLK and second try with GND, SWDIO, SWCLK...
Hi,
Please let me what is the beacon layout of nRF58122 for scanning beacons in region by using following method:
BeaconManager.getBeaconParsers().add(new BeaconParser...
I'm using and NRF52 with S132 and SDK13.0. I'm using Keil as my IDE.
My application acts as a central for smart phones to connect to and also acts as a peripheral to conect...
Hi, I'm a mechanical engineer, an industrial engineer and have a master's degree in control of the dynamics systems. I never get the change to work with ARM architecture before...
Help, what UART output pins that gather all information from the various sensors in the NRF52832 thingy52, to integrate with Raspberry or Arduino, thank you
Hello Community,
I am trying to implement a whitelist in my central device but when I type ble_gap_whitelist_t I had an error of compilation becuase ble_gap_whitelist_t...
Hi,
My first objectif is that the Micro:Bit consumes less than 2μA without the BLE. I read that the Micro:Bit program was not powered if the Micro:Bit is powered by the...
