Hi ... have code that outputs I2S in master mode. The slave, a NAU8822 device requires Master Clock Source between 8 and 33MHz.
The 54L MCLK pin is duplicating the BCLK...
Hi,
1.How to modify the transmission power of the example direct_test_mode to 4dBm? 2. Please provide Method 1 and modify it using the CONFIG configuration? 3. Please provide...
Previously, I designed a PCB for the nRF52832 chip using the RFANT3216120A5T antenna ( link ). However, I was only able to achieve a very limited Bluetooth range of around...
Hi, I'm relatively new to Nordic microcontrollers and have recently completed the beginner's course. Sorry in advance if I made an obvious mistake.
I am currently trying...
We are running a nrf54l15 board that uses an NFC T2T tag to encode a URI to open an application. We have noticed that sometimes, the current stays higher (~200 uA) after the...
I’ve got a bit of a hardware issue with the nRF52811 UART, receiving DMX data from a Chinese DMX controller.
Standard DMX data-rate is 250Kb/S, so the minimum bit time is...
Hi,
I am using the Nordic UART Service (NUS) peripheral and central on two nRF52840 DKs and I am developing with nRF Connect SDK v3.0.0 .
I can't manage to increase the...
I want to enable BLE's NUS Service(in Old SDK, nRF5_SDK) with in nrf5_SDK_for_Mesh.
Is it possible?
I'm failing, as starting of this, to use Softdevice for parallel use...
I HAD ASKED THIS QUESTION: we have used the NRF51822-BEACON KIT EVAL BLUETOOTH SMART BEACON which includes RGB LED, but cannot find a non dev kit model with RGB LEDs . can...
Hello sir,
I have develop project and their lots of quantity. I want flash my updated program into my nordic device without open this device via BLE services. Is it possible...
Found on the web:
"Properly configured WiFi network shouldn’t interfere with the Bluetooth signal. The best practice for WiFi configuration is enabling WiFi on one of the...
Hi
I have a project use nrf52 to have a purpose below.
Maybe after some pairing process with smartphone.
The user can trigger the device(nrf52, may press a button...
Hi guys,
I am trying to connect my BLE Nano 2 with HM-10(as a Peripheral device) using Arduino Central_test program.But the problem is it is not pairing with it,but detecting...
Hello,
We try to use "ATT_MTU" and "Data length extension (DLE)" to expand a packet in S132 SDK 14.0.0.
When we set "ATT_MTU" > "DLE", please tell me what happens?
...
i am in very strange problem and was unable to debug it
i am using following code to write 16 bytes data to flash memory, my app hangs after executing custom_flash_write...
Hi all,
i'm trying to use the function of power warning with s132 and nrf52 with sdk 11.
i use the function
err_code = sd_power_pof_threshold_set( NRF_POWER_THRESHOLD_V27...
I am running example: nrf5-ble-tutorial-advertising on a nRF52-DK.
with SDK 11 and s132_nrf52_2.0.0 softdevice.
When I flash the code to the nRF52-DK, LED1, LED2, LED3 and...
Hello,
I'm using Ceedling, Unity + CMock to implement unit tests but I'm running into issues when it comes to mocking nrf_drv_gpiote.h.
I'm trying to test a file, call...
Hi Nordic Engineer, I refer to your previous post title "Running micro-ESB concurrently with BLE" and gonna to use it on our project.
I test it on 4 pcs of DK board, found...
I have a problem using ble_advertising_restart_without_whitelist(). According to the documentation (as I understood) it should start advertising without whitelist even if...
Hi all
When i am reading ANCS code, i have some questions. SDK 12
Question 1: when ble device are connected with ios, the pairing is wrong, how to handle validation...
