Hi. I'm trying to write a simple MQTT app. I am consistently getting these KConfig errors to do with variables I'm not using, and I have tried to set CMake to ignore these...
Good day,
I've developed a board with a MDBT50Q on it. I'm using the Reg0 DC/DC and LDO Mode Disabled reference circuit ( https://www.raytac.com/download/index.php?index_id...
Hi,
I have the issue that my Zigbee device reports the error "Production configuration is not present or invalid (status: -1)". I followed the guide from this( https://docs...
Hi,
I am using an nRF52840 as a Zigbee NCP. I have built the firmware myself using nRF Connect, and I am also running MCUBoot. Sometimes after some usage, the chip starts...
Hello everyone,
I am testing out I2C on the nRF54L15 for a custom PCB project.
I first tested a simple mpu6050 sensor on &i2c21 on pins P1.11 for SCL and P1.12 for SDA...
I have a bit of an unusual use case where the nPM1300 is quite ideal but need to use an external charger for the battery instead of the internal charger. The nPM1300 fuel...
Hello,
We are currently developing with the nRF9151 and would like to request more information regarding GNSS SNR testing.
We have reviewed the documented GNSS functionality...
Using Keil MDK Lite v 5.22, writing code in C for nRF52, with SDK 12.
Example code works.
How does one declare a function, define it, and call it?
I've created a...
In my debugger, I see that variable error_code is 0x00000004
void app_error_handler_bare(ret_code_t error_code)
{
error_info_t error_info =
{
.line_num = 0,
.p_file_name...
I'm running a debug session.
I set a break point inside of function services_init on line 201.
I ran the run up to break point command
The processor pauses on...
Hi,
i am trying to save data with the flash data storage module. Using this code ( infocenter.nordicsemi.com/index.jsp from infocenter erverything works fine. But when...
I am attempting to do a BLE firmware update via command line tools in an attempt to automate programming in a script file. I have zero problems performing an over the air...
In a project using esb, with two nrf52832 devices configured as default, one as RX, one as TX, with dynamic payload, TX sending packets to RX can change the packet pid (and...
Hi!
I have two PCA10040 boards and I'm running the MQTT publisher example in both using a Raspberry Pi 3 Model B as a gateway.
Therefore, both boards are establishing...
Hello,
I am using pca10028 and sdk 12.2. I am trying to run some code. I am getting some make file error as ble_nus_error.PNG .
My main.c file is New Text Document (3...
Hi,
I have 2 nRF512840 eval kits and tried out the att_mtu_throughput example provided on SDK 13.0.
The throughput about 900-1000Kbps can be achieved with PHY 2.0 DLE...
Is there any way that I can use more than 4 timer in nRF 51 ??
(four or more...)
I'm using Softdevice 130, so It uses Timer 0,
and I'm using RGB Sensor using PWM Library...
i m new in NRF52832, i use saadc exemple pca 10040 sdk 13.0.0, i dont now how to get adc result from the buffer because there is 2 elements in the buffer :
err_code = nrf_drv_saadc_buffer_convert...
Hi, Nordic Forum!
We've been trying to implement an adapted version of the Secure Bootloader with Buttonless DFU in our custom board. We have successfully accomplished...
