why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
I am looking into using Internal RC instead of External Oscillator (with softdevice on).
The function ser_app_hal_hw_init() uses Xtal clock source by default.
...
Hi, everyone. What is the meaning of datasheet "section 8.5.7 Antenna matching network requirements"->15+j85 ?
Whether is that we can caluate the 50o with the data?
bonjour , j'ai essayé de communiquer deux pca10028 en utilisant l'exemples " transmitter_pca10028 et receive_pca10028 " mais l'experience a echoué je sais pas pourquoi sachant...
Hello,
I'm testing current time service client example on SDK 8.0.0 with iOS.
After connected the devices, iOS show confirmation to pairing.
When I canceled this or...
After enabling and starting the watchdog timer (RR0), how can it be disabled?
This following code does not work :
NRF_WDT->RREN &= ~(1 << WDT_RREN_RR0_Pos);
Neither...
Hi,
I use s120 stack and ble_app_multilink_central
I use function sd_ble_gattc_primary_services_discover(p_client->conn_handle, start_handle, NULL) for discover services...
The sniffer software doesn't seem to find the device on either of two different PCs here, and I'm not sure what we could be doing wrong.
The installation steps were the...
Hello,
I have recently got a n5 start kit nRF51422. I went through all the set up procedures in the user guide, installed all the correct programs/drivers etc.. My unit...
Hello.
I am looking at the schematic of the nRF51422 USB dongle development kit. The pin P0.30 of the microcontroller is attached to ground. As the pin could potentially...
I'm writing a PC utility in Visual Studio to connect to BLE devices. I'm using the PCA10000 and MasterEmulator.dll. I'm able to discover the services and characteristics of...
Hi NORDIC
I download the example of multilink central (S120) into nrf51822 . I do not know why it can not work ? My SDK is s110_nrf51822_7.0.0_softdevice . Please help...
i am very confused about how to count pulse by using nrf51822? I am going to make a heart rate counter, but i don't know how to config registers to achieve this function....
I can't get a simple application, no soft device, to debug on the nRFDK 10028 board using the I-Jet. I am using the debug in and powering the device from an external power...
Hi
I'm starting with NRF51822. I'm going to develop a costum PCB using this chip. I'm a bit confused because searching on the forum I saw that I need a product key to use...
