spim2、ncs2.6.1
I used SPIM2 to send the string "Hello, SPIM!" and receive data of the same length.
However, on the logic analyzer, I can only see the transmitted signals...
I am using nRF52833 PCA10100 board. While trying to run sample ble code in segger embedded studio, I am frequently facing this error which says, .text file is larger than...
I am developing an server app on zephyr stack which requires to flash the image without SMP protocol, I receives the image data over BLE , how can I use Image management API...
Hi,
I am trying to program the custom nRF9160 board using SEGGER JLink/SWD programmer , For same of the boards when connected to custom board and trying to select the device...
Hello,
we are using a nRF5340 with NCS 2.9 and want to signalize a
UART_LINE_CTRL_BREAK
on USB CDC_ACM to the PC.
Is there a direct way to do this?
Many thanks in...
I am analyzing the power consumption of a custom board with an nRF52833 BLE SOC and nRF21540 FEM for different BLE parameters. In one of my experiments I vary the amounts...
Is there a straightforward way to output the frequency of the 32.768kHz crystal oscillator to a GPIO pin? The motive for this request is to verify the crystal frequency without...
I'm unable to get any output when writing to the UART while using the s110 softdevice. I'm refering to the hardware UART. I'm not using bluetooth for serial.
I'm using...
Hello,
I wrote a firmware for my project, based on the UART over BLE example, so using the softdevice, establishing connections, etc. It works.
I'd now like to use a...
Hi all,
I can program and debug my application just fine when the softdevice is not used (initialized). Problem is, when I do use the softdevice, I end up in Hard Fauld...
Hello,
In our prototype (Embedded System) we want to use nRTF24AP2 with Chip Antenna, as W3006, for example.
Our questions are: where and how needs to be placed the Chip...
Hi there,
I currently have an nRF51 DK set up transmitting six 20 byte packets per 7.5ms, there about, to an nRF51 Dongle set up as a central. When viewing with Master...
Hello,
I would like to move on from using nrf_delay_ms().
I thought this would give me some first results, but It don't. Whats wrong?
//a
static void test_timer_handler...
Should be noted that i'm using nRF51822 breakout board and i have a lot of problems with its programming. And i'd just begun to write own topic about my problems with connection...
Hi,
I am playing around with the BLE_proximity_template on the Redbearlab BLE shield and an Arduino Uno. I uploaded the sketch and paired my Android Lollipop device with...
I'm a beginner and have been using library provided by the nordic to communcate with nrf8001. I read nrf8001 data sheet but couldn't understand how to use the aci commands...
Hi,
I want to get this dongle to 'see' the data being transmitted to and from the nrf51 dk. I saw a note here adafruit saying
The sniffer firmware cannot be used...
Hi,
i wuold like to control one port of my home gate's centraline by Ble shield on Arduino.
I need to send an impulse for 1'', no more. Like a release button, not like a...
Got it working .. forgot (didn't know) I had to change the attribute length as well
I am currently trying to figure out where/how to attach my measurements so they can...
We've been using the nRF51822 sniffer to listen to packets. One of our developers used to be able to use it decrypting packets without a problem (He uses 32-bit system, firmware...
S110 v8.0.0 / ble_app_hrs_with_dfu
I want to enable whitelisting.
In the advertising_init() function I have:
ble_adv_modes_config_t options = {0};
options.ble_adv_whitelist_enabled...
