Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
I'm unable to get any output when writing to the UART while using the s110 softdevice. I'm refering to the hardware UART. I'm not using bluetooth for serial.
I'm using...
Hello,
I wrote a firmware for my project, based on the UART over BLE example, so using the softdevice, establishing connections, etc. It works.
I'd now like to use a...
Hi all,
I can program and debug my application just fine when the softdevice is not used (initialized). Problem is, when I do use the softdevice, I end up in Hard Fauld...
Hello,
In our prototype (Embedded System) we want to use nRTF24AP2 with Chip Antenna, as W3006, for example.
Our questions are: where and how needs to be placed the Chip...
Hi there,
I currently have an nRF51 DK set up transmitting six 20 byte packets per 7.5ms, there about, to an nRF51 Dongle set up as a central. When viewing with Master...
Hello,
I would like to move on from using nrf_delay_ms().
I thought this would give me some first results, but It don't. Whats wrong?
//a
static void test_timer_handler...
Should be noted that i'm using nRF51822 breakout board and i have a lot of problems with its programming. And i'd just begun to write own topic about my problems with connection...
Hi,
I am playing around with the BLE_proximity_template on the Redbearlab BLE shield and an Arduino Uno. I uploaded the sketch and paired my Android Lollipop device with...
I'm a beginner and have been using library provided by the nordic to communcate with nrf8001. I read nrf8001 data sheet but couldn't understand how to use the aci commands...
Hi,
I want to get this dongle to 'see' the data being transmitted to and from the nrf51 dk. I saw a note here adafruit saying
The sniffer firmware cannot be used...
Hi,
i wuold like to control one port of my home gate's centraline by Ble shield on Arduino.
I need to send an impulse for 1'', no more. Like a release button, not like a...
Got it working .. forgot (didn't know) I had to change the attribute length as well
I am currently trying to figure out where/how to attach my measurements so they can...
We've been using the nRF51822 sniffer to listen to packets. One of our developers used to be able to use it decrypting packets without a problem (He uses 32-bit system, firmware...
S110 v8.0.0 / ble_app_hrs_with_dfu
I want to enable whitelisting.
In the advertising_init() function I have:
ble_adv_modes_config_t options = {0};
options.ble_adv_whitelist_enabled...
