Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
Hi everybody.
I am making a firmware based on ble_app_uart example (PCA10028 NRF51422, Softdevice S110, NRF51 SDK9.0). In this firmware, I insert dfu part ( follow by this...
I am testing out the Bluetooth Mesh SDK 0.9.1 Alpha using the light control client/server example. The examples have not been modified.
I have set up a nRF52 development...
In android while at the stage of scanning there is list of ssid ,i am getting print of scan_result but while trying to print the RSSI value,the result is 0 .Files i have changes...
With our custom board, I have implemented the battery service and it's working well. But the nus service is not shown up at all, the same initialization code as the official...
i use the nrf52832,s uarte. using the app_uart_fifo.c document. but i can only receive the max 256 bytes.the configuration is belows:
APP_UART_FIFO_INIT(&comm_params,
...
Hello,
Is the characteristic value data supplied to sd_ble_gatts_characteristic_add() and sd_ble_gatts_value_set() copied into the softdevice RAM, or does the softdevice...
.pdf d051cefddbc197cd7d)
Hello All,
I am working on Automotive project using nrf51824 SOC...
Hi,
I am working on making a test harness using the nRF52DK and a raspberry pi so I may run unit tests directly on the nRF52832. I want to use the UART to give test results...
We recently did pre-compliance RF radiated immunity testing at a certified lab. The EUT was nRF52832 on a battery powered post card sized circuit board with some sensors....
when I run the program I get this error
Checking installed packages
pyside: 1.2.2
pyqtgraph: 0.10.0
numpy: 1.11.3
pynrfjprog: 9.1.0
Warning: The software is tested...
I am using a PPK with v1.0.0, but elsewhere in DevZone I see references to later versions of the software. Where can I download the later versions from? Have I missed a link...
Hi.
Great that you have added logging capability to the PPK desktop app. This was exactly what I needed.
I noticed one minor issue with the logging: When starting logging...
I have an application with hard real-time requirements (i.e. down to the clock cycle). My topology and desired timeline can be seen below. Concerning the timeline, I believe...
Hello,
I have a question regarding app interrupt handling.
When an Application Timer Interrupt is being handled, can it preempted by a higher prioritized interrupt of...
Hi,
I have used this antenna for my nRF51 layout, but it seems that the device is using very high currents! like in order of 200mA, I just wanted to know if this is because...
