Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hello All
We are trying to integrate ST7305 driver with NRF connecct SDK and are unable to get the driver to work using the extrnal module method mentioned in the NCS Intermediate...
My device tree overlay GPIO section looks like this:
Note that I repurposing a GPIO that was used for an LED in the board's device tree file. Also note that node numbers...
Hello,
I am using the nfc_system_off example code to evaluate the characteristics of power off mode.
Current measurement is done by following the instruction shown in...
I am trying to use Health SRV and Health CLI to check if there are any errors in the nodes. I have successfully transmitted the fault codes, but there are still many questions...
Hello
I created the out of tree sample sensor application with SDK 2.6.2 and it built just fine However it builds only when it is inside the sdk that was pulled when I selected...
Hey everyone. I am having an issue reading the WHO_AM_I register from the stm lsm6dsv16x. I am using the spi1 configuration as shown in the academy classes. I have very short...
I am using an nRF52840 USB dongle to sniff some Zigbee packets for a product I am developing. I am trying to use Wireshark to decode the messages shared. I followed the steps...
Hi,
I'm using nRF9160DK with SDKs v3.0.0
I am trying to use A-GPS with nRFCloud REST. I used the location example and it works correctly. The documentation states that...
Hi, I am using the nrf54L15DK to take some current measurements. I am using the PPk2, connected to P6 on the DK, supplying 3V, and have the USB on the DK connected. With a...
Reference states a +/- 3% tolerance, which is rather high. 1. Do any of the reference voltages exhibit a better tolerance? 2. Is it possible to roughly model the tolerance...
Hello Nordic team,
After many hours I have not been able to get socket dispatching working with Zephyrs MQTT client, and I am not sure how to proceed.
First of all I would...
Hi, We’re trying to develop a way to create fully self-contained repositories that include:
-the toolchain
-the entire SDK
-the necessary tools (for example, flashing...
Hello,
I just got nRF54L15 DK and Im getting this error when flashing it:
Im running on a mac, have NRF Connect installed along the command line and 2.8-2.9 sdk...
I wanted to know if this program starts sending advertisements using the Coded PHY OR if it starts advertising in the normal advertising channels using the normal 1Meg output...
Hello, I want to build serial_lte_modem sample for a custom board based on nRF9151, but it fails with this error:
error: Aborting due to Kconfig warnings
I can build...
