Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hi
I have an application where I cannot use the FIFO buffers (HW or SW). Therefore I need an interrupt for each received byte. If I try to use the uart driver (nrf_drv_uart...
I'm trying to program my nrf52832 with an ST-LINK /V2. I can't get both the softdevice and my app on the chip.
Flashing each one seperately works fine but then when I flash...
Hello there,
I'm trying to flash my custom nrf52832 pcbs(untill I get my DKs in the tech tour with a reconfigured stm32 disco board's SWD port with keil uVision using the...
Hello.
This is my code to "wait until micro sd card is pluged".
while(1)
{
disk_state =disk_initialize(0);
if(disk_state==RES_OK)
{
NRF_LOG_INFO("Initialize...
Hello community,
I have a central device which I implemeted, it is running with SD 132 v 4 ("NRF_SD_BLE_API_VERSION=4")
) the chip is a NRF52832, I have some movement...
I have no idea how i can install this and use it.
I would like if any one can explain in detail.
Can you get picture how I can do it?
I am using ble_app_hrs_nfc_pairing...
Hi,
As of now i am using nRF52840 and SDK 14.0.0 and i can find only BLE examples and i wanted to work on bluetooth 5 where can i find examples?.
And i want IR generator...
Hi ,
I am not sure if it is the right place. I was looking for WiFi: 802.11 b/g/n 2.4 GHz support in Arduino UNO and stumble into Arduino primo, which is developed in cooperation...
Hi,
I would like to only connect certain routers in a network using whitelisting. At the moment I'm trying to set a dedicated MAC address to a router and then use this...
Hi,
I am trying to implement the DFU ANT Bootlaoader on my PCA100040 board. I have uploaded the softdevice S212 and the bootloader with nRFgo Studio. I have an ANT dongle...
Hi, I want to read the StaticPasskey from the Softdevice that was set before with:
uint8_t u8_ToBePassKey[];
/*
* Configure ToBePassKey in some way...
*/
m_static_pin_option...
Hi everyone,
I am developing a remote control using nRF52832 chip. My prototype is currently developed in PC10040 board. The IDE is Eclipse Oxygen, and the SDK is S132...
According to here , pstorage_init should not be initialized twice.It links to another thread and the documentation which says the same but does not mention downfalls of doing...
