Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi, I use IoT sdk with my iPhone to get current date and time, date comes in ble_cts_c_evt_t structure, how can I convert it to timestamp, I know that I have to subscribe...
Hello all,
As i want to lower the power consumption, may i know if its possible to connect the supply voltage of ntc thermistor to any gpio of nrf52832 instead of directly...
Hi,
I'm using the NRF52840 Preview DK and want to create my own BT stack with high throughput between NRF52 and other BT devices.
As base I'm using the ble_app_template...
Hi,
I followed the link, gnu-mcu-eclipse.github.io/.../ , to setup my debug environment before. I was able to view the registers. However, I updated my eclipse and the SVD...
I use the nRF52-SDK on an nRF52840 PDK, but if I start a scan request, I don't get the number of scanned channels back in the mlme_scan_conf_t.
I.e. mlme_scan_conf_t::unscanned_channels...
Hi! I need to understand the basic functionality of BLE Mesh.
Please see attached picture.
1. Is it true that a device (eg BLUE) through BLE mesh can communicate DATA...
Dear friends,
Software &Hardware: Power Profiling Application (a SDK example), S132 softdevice, nRF52832(PCA10040), Power Monitor. The measured average current consumptions...
What is the maximum sampling rate of nrf52832? I used the ppi on nrf52632 to collect the signal on gpio. After testing, it was found that when the signal on gpio is greater...
Hello all,
I want to built a coin cell powered thermometer with NTC thermistor.
May I know if I need to regulate the voltage from the coin cell or i can power the nrf52832...
I have a problem with the 802.15.4 software part of my nRF52840 PDK. I wanted to replace our current 802.15.4 hardware parts from TI with the new nRF52840, due to the lack...
Hello. We are now starting our review to customize code for the pending use of the Nordic devices in low power mode. Have a mix of Nordic kits now. Using the nRF52832 (PCA10040...
Hi,
I am trying to implement buttonless DFU by following the ble_app_hrs example provided in the SDK and modifying the bootloader (nRF51_SDK_10.0.0\examples\ble_peripheral...
We have our custom PCB design that we program and debug by connecting the SWD lines to nrf51 DK's SWD. We wanted to use trace for better debugging options, however we discovered...
