Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
I am trying to communicate with iPhone X using Nordic_Uart sample project in SDK 14.2.
And I check the Protocols between nRF52DK and iPhone X by using Ellisys Bluetooth Tracker...
Hi,
I'm using nrf52840,
I'm using SDK 15.
I can see that in nrf_drv_power_pof_init function only few power setting are allowed - is that true? can I only use those values...
Hi all,
I have a NRF52DK acting as a peripheral and running the ble_app_uart example. I want to have bi-directional communication with a mobile device that is connected...
Hi, I'm currently trying to make a flash logger using the nRF51822_XXAB. My logger is also advertising temperature, battery and other informations in beacon form. I also want...
mesh sdk: nrf5_SDK_for_Mesh_v1.0.1_src
example: light switch client + light swtich server
My problem is that the client cannot remove the server.
I found that many developers...
Hi All,
I am doing the certification (Japan Radio Law) now. I use the nRFgo software to enter the "Direct Test Mode" for test the each channel BUT I do not know how to...
I have designed nrf52832 customized board with tace antenna antenna and every pin of the controller is connected to the male headers present on both side of the boards. I...
I am using sdk 14.2.0 and I want to use nrf_calendar.h in my code but it is supported only in sdk 13.0.
will you guide me how can I use it in my sdk version 14.2.0.
the...
Hi,
Would someone please help me to configure a specif channel for continuous scanning. I was browsing through the forums and understand that the SDK/SD not supports these...
Hi together,
since quite some time I try to merge my BLE application with the SPIS functionalities from nRF52 SDK 12.3 example with softdevice S132. My application should...
Hi, I am developing a central device application using the ble_app_multirole_lesc example as a baseline. I am using v11 of the SDK. This example uses the heart rate service...
I am following the Thread Border Router example and have successfully loaded RaspPi_OT_Border_Router_Demo_v1.0.0-1.alpha.img onto the RaspberryPi 3B+.
I have loaded the...
Scan of services after connecting to DFUTarg does not return
the new services on the device. Instead the old services that existed
on the device before going into DFU...
I'm trying to follow the guide Sending mesh packets in the Interactive PyACI section on the nordic infocenter.
I've installed the required prerequisites using pip.
Here...
