I have a nRF54L15 firmware built on NCS v3.0.1, with image encryption enabled in mcuboot. Firmware needs to be updated to new version built on NCS 3.3.0.
In NCS 3.0.1, image...
Hi folks,
I am working on an nRF52840-based custom board using nRF Connect SDK v3.2.4 and have observed an issue related to runtime power management and PWM.
Environment...
Hi, is there a sample using nRF7002 on nRF54LM20B SQSPI (or could you share an appropriate devicetree)? I have been successful using the nRF54LM20 DK + nRF7002 EBII combination...
Hello.
I have nRF52840 USB Dongle connected to PC with nRFConect desktop application 4.0.4
I'm trying to connect to our custom BLE peripheral device, which advertises...
Hi all — I'm developing a custom nRF5340 development board (Raytac MDBT53-1M) and would value the community's honest read on whether it's worth producing.
The goal is...
Hi,
I am using two nRF52833 devices with the nRF5 SDK. They are paired and bonded to each other. Occasionally, I encounter the following error in peer_manager_handler :...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Hello,
I'm using a module based on the nRF52810, the Fanstel BT832A. I'm running the basic "ble_app_beacon" firmware from the "nRF5_SDK_14.2.0_17b948a" SDK with a few changes...
I spent a few hours trying to change the base UUID and handles of the attributes of the Blinky peripheral app, just the one service and the button and LED characteristics...
I have couple of nRF51422 boards, nRF5-SDK-for-Mesh (v. 1.0.0) and good will to demonstrate some simple multihop mesh.
And I want to write some data to the flash, but operating...
Dear Nordic,
I are using nrf52832 to develop a product that needs FCC certificate,
We use a PA and can increase the output power up to 20 dBm and it
seems that is lower...
Hi guys, I’m doing several tests with my new RedBear BLE Nano v2 board based on nRF52832 using the RedBear library, but I found a problem with reading Notify Characteristics...
Hello,
I need time synchronization between the two devices. At the same time I want to use the standard means of bluetooth, synchronizing the clock of the connected devices...
Hello,
This is the first time I try to implement DFU to update my simple application OAT via BLE on the nRF51 DK.
My simple application is a simple peripheral which...
I have a GPS over UART to a nrf5283. For debugging the GPS, I'd like to passthrough UART from my PC to the GPS. I know the nrf5283 only has one UART. Is there a simple way...
First about my setup: custom devices with NRF52832 chips (SoftDevice 132 v.4.0.2), android smartphones Nexus 5x and 6p.
I'm trying to connect as many BLE devices (peripherals...
I'm working on a custom board with an nRF52382 connected to an IMU over I2C. The IMU provides 2 separate interrupt signals, and I would like to route each of them to a separate...
Hello,
Today I've a strange behavior of nRF51 DK (everything was working ok until today, the last things I did was to reset the J-link FW after a total erase of the board...
Hi all,
My configuration:
nrf52832 microcontroller
Softdevice S132 V4.0.2
Nordic SDK 13.0
I'm using an "app_timer" in repeated mode with 10Hz frequency...
I have recently acquired a NAND chip from Micron and would like to use it for storage.
However, looking through the datasheet I found out that the addressing scheme require...
