Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I'm develping my application with nrf52832 and nrf SDK v17.
I'm testing SPI interface so that I can use the external flash.
When I using SPI without BLE stack,the waveform...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
I'm developing with an NRF52832, using NCS v2.6.1/Zephyr 3.5.99
My custom hardware has three NXP PCA9538 GPIO expanders on it, to allow me to control various address and...
Hi,
Our products have been mass-produced and now need BQB certification, but the certification fails.
IC：nRF54L15 ncs2.9.1
base project: ncs_v2.9.1\v2.9.1\nrf\samples...
My product currently has DFU (Device Firmware Update) functionality enabled, but I want to allow firmware updates only after receiving a specific command via BLE. This is...
Hi everyone,
I'm new to both nRF Connect SDK and Zephyr RTOS , and I’m trying to modify the official LittleFS FileSystem Sample to mount an external SPI flash as the storage...
I was implementing custom services and characteristics(softdevice:s140, ble) on the nrf52840 dongle, however I couldn't get it to work, even though my code seemed correct...
I think this code snippet is causing the issue, since I am able to make the device work by setting:
' NRF_SDH_BLE_PERIPHERAL_LINK_COUNT = 1' and 'NRF_SDH_BLE_TOTAL_LINK_COUNT...
Hello,
I am using Nordic Thingy91 5G board. My modem firmware version is 1.3.6. My nRF Connect for Desktop version is 5.2.0, which has a Serial Terminal version of 1.5...
Hi
I've an application running on nRF Conenct SDK 3.0.2 on an nRF52840DK. Now I tried to enable update support over serial recovery of MCUBoot using the USB ACM.
First...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
We are currently working on a project using the Nordic nRF5340 and nRF7002 DK, which includes 1MB of internal flash and 2MB of external SPI flash. Our application codebase...
Hi,
so i was using the NRF51822-QFAC with an external balun and this antenna chip 2450AT43A100E .
now i want to move to the nRF52832 chip and from what i read is that...
Dear Experts,
I would like to better understand what exactly is accomplished by the mode-0 synchronization in Channel Sounding. My current understanding is that it seems...
