Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi Nordic Team,
In a BLE project we need to configure same device to conditionally act as central (to scan) device and peripheral(to advertise) device based on the state...
If I write to the MWU REGIONENCLR register and immediately access memory that was previously watch enabled an event is still generated. If I delay a small amount (tested with...
Hello,
we have made our fist device with a custom Service with 5 characteristics. And now we have a strange problem which I was not able to debug to find a solution.
We...
Hello,
if I call this code all works:
if I call following code only ZB_ZCL_ON_OFF_SEND_ON_REQ take effect on target
I'm simply swap the call order, where's the error...
Good morning everyone,
I saw this question asked a few times, but no conversation was actually fixing the issue.
I am developing a product where I want the pairing to...
This seems to have changed in recent SDKs, so that none of the examples or techniques mentioned in previous posts is relevant any more.
I am using the SDK v16.0.0 ble_app_blinky_c_pca10040_s132...
When I carefully follow the instructions at https://infocenter.nordicsemi.com/topic/sdk_tz_v4.0.0/thread_ot_libraries_building.html , I am missing some of the openthread libraries...
Hello.
I just started using nRF52840-DK board with SEGGER Embedded Studio and I'm trying to use it to save data in a micro SD through an adapter. I tested it with the Fatfs...
SDK15, nRF52832, S132
I notice that after about 30-50 bond and delete cycles peripherial to central, central doesn't want to bond. Before it bond and after that delete bond...
Hi there, I am working on controlling the nRF Mesh device (nRF52840-DK) via the bluez version of 5.52 (meshctl). I try to connect to Nordic nRF52840-DK (example <nrf5_SDK_for_Mesh_3...
Good morning,
Is it always required to use Segger J-Link in order to flash Bootloader, Softdevice and Application to a new device?
Could you summarize the different possibilities...
I have an application where I will require an external antenna as our product sits in a metal enclosure.
The example NRF91 DK development board shows a UFL connector (which...
Hi
I want to know the address of the memory used by FDS.
I set the following
I think , this setting uses 3 pages.
However, there are tags at 0x2D000 and 0x2E000...
We have a problem that we are struggling to solve. We have written an application for the Nordic Semiconductor nRF52832 which uses a proprietory radio protocol. This protocol...
Hello,
I have a question about a certain issue that came up during developing a 3 transmitter, 1 receiver setup.
So the basic setup is that the transmitters are sending...
