Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello everyone,
I'm working in an application where I need to store a string in flash so I can keep that value like if it where settings when doing a firmware update so...
Hi,
I've got a question regarding voltage compatibility. The nRF52840 will be driving many LEDs. Would it be possible to use a separate 5V supply with the LEDs and use the...
Hi,
I am developing a Linux PC application interfacing nrf52840 dongle using pc-ble-driver v4.1. I am trying to use the Long Range feature with Coded PHY. The setup in like...
Hello:
I want to do OTA with Mesh DFU using nrf52832. Now I make sure that DFU works correctly in the mesh and the host can receive the package from the server. The problem...
I am developing a proprietary test system that will use Bluetooth mesh and am evaluating BT mesh solutions. An important consideration is the available support for a windows...
Hi All,
We have developed the firmware for our device from the ble_app_bms example. The project is already in production.
Our customer hs nov decided that they want to...
I have encountered this issue while trying to trigger a ble_nus_string_send() - function from anywhere else than in the ble_rx_handler.
I use Softdevice S110 on the NRF52832...
Hello,
I am porting several of our devices which implement ZCL from another stack vendor to run on Nordic. These are legacy devices that support Report Configuration/Reportable...
Hello,
Our device has the secure BLE DFU enabled. In a mass programming situation we need to apply a hotfix to each device and replace a previously hardcoded value with...
Hi, Cloud is NOT getting connected. Actually I am working on nRF9160 DK (PCA10090) past 3months. I was successfully able to register the DK broad with nRF cloud account and...
Hi,
I try to do the DFU example in the nRF5 Mesh SDK V4.0 for the nRF52833 Development-Kit:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hi,
Our company offers product with and without Bluetooth. The nRF52810 chip will always be present on the hardware, it will just be programmed to either have the radio...
So I am initializing the FDS but the program I guess stands in an infinite loop at wait_for_fds_ready():
This is not working. At the moment I have given a delay of 300ms...
Hi
OS: Windows 7 (32-bit)
nRF Connect application: v3.1.0
Getting started assistant: v1.0.1
Please see the attachment. After installing ninja, tried to verify it...
Good afternoon,
I'm developing my application based on nRF52840 and S140. What I pretend to do now is to make it possible to update device software (softdevice and/or booloader...
