Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am working with nRF51422 & would like to know if I can measure current of single event & multiple events (pictures attached) as detailed as possible. I have cut...
Hello everyone.
I want to increase the operating range for nRF51822. To do this I added PA SE2576L in design.
Unfortunately, I do not have experience in RF develop...
Hi,
I'm attempting to use Version 2.1.0 of the HomeKit SDK on an nRF52. We're using the s132 SoftDevice 2.0.0-7.alpha (the SoftDevice in the latest nRF5 SDK v11.0.0). ...
Hi.
So my problem is, that i cannot successfully program external board with preprogrammed nrf51822 chip in the board.. This board is from china.. its an ibeacon.. If i...
I've recently been playing around with Bluetooth Developer Studio, and I can see it's potential despite it having a few annoying bugs.
I've set up a custom service by re...
Where would be a good place to feed a watchdog when using a softdevice?
My first guess was in main loop:
for (;;) {
NRF_WDT->RR[RR_number] = 0x6E524635;
power_manage...
Hi,
When a watch dog timeout occurs, I want to save some data to the flash memory prior to reset (namely the RTC count value). Therefore I enabled the wdt interrupt. The...
Im using nrf51, I configured the watchdog to reset after 3 seconds of hang and it works. But I have absolutely to save some data in flash before reset
Is there anyway to...
My custom profile was being built fine until I added a couple of standard descriptors to a custom service characteristic. Any idea what's going on here?
19:34 - [Code Generator...
Hello All,
I want to develop bluetooth mesh using NRF51.
I have question about this:
Is their library closed or not?
Do we need smartphone like in CSR?
...
Hi, I have a TinyShield Nordic module and I am having some troubles trying to customize the advertising packet. I have downloaded NRFGO Studio and I have enabled service data...
I have an nRF 52 dev kit, an Asus router running openWRT, and an android phone with the master control panel.
I'm able to compile and flash the dev kit with the example...
hello,
I am using the nrf51822, I want to add a normal service which do not need bond before used at the ancs example.I hope it can do the follow tow points,firstly,if the...
Hi,
I tried to figure out what is happening on the lower Bluetooth levels but it is very difficult to find straightforward information. Especially the Bluetooth (4.2) standard...
Hi, My apologies that this seems repeat information from previous posts, however they do not give a clear answer to my question regarding 4.2 compliance. I must also state...
