I've been trying to flash an nRF52840-DK with code that successfully builds on Segger. The Segger error is "Failed to connect to target." I updated the devkit firmware with...
I am trying to set up a w25q128 using SPI with a nrf5340 on a custom board and had a few questions. I have used DevAcademy as a reference as I do eventually want to set up...
I have a custom board with nRF52840. It draws power over USB and the data lines are connected as well
USB is defined as follows in the dts
cdc_acm_uart0: cdc_acm_uart0...
Im tring to generate sbom in html or spdx format yousing west ncs-sbom -d build i got this error: package.name += '-' + package.version TypeError: unsupported operand type...
Hi there, I'm facing difficulties configuring the Adafruit ILI9341 with the nRF52840. Are there any beginner-friendly instructions on how to configure and program it over...
Hi,
I have two nearly identical revisions of a board with an nrf5340 which behave differently in a curious way:
On one revision I can issue a "mon reset" command in...
Hey Team,
I'm trying to flash the audio application on our custom PCB, this PCB follows the interfaces of the nrf5340 audio dk. Previously on lower SDK versions (2.7-2.9...
Hi,
I am working with the ble_app_uart (central and peripheral) example and they already run fine. Now I discovered that some button actions are already defined on the...
Hello,
I have created the simple software usign NRF51DK to make the led blink for 5 times by using while loop
just to make the other part of my software
my aim of this...
hi，i have a question.
i set the advertise type to BLE_GAP_ADV_TYPE_ADV_NONCONN_IND MODE, and i add scan response data,but i can't see scan response data.Why?
Hi,
I would like to connect nrf8001 to a Renesas microcontroller but I could not find any documentation on how to proceed with this step. The only documentation I could...
The ADC module requires that the output impedance of the connected voltage source be 1kohm or less (section 31.1.3 of RM).
Does the same restriction apply for the LPCOMP...
Im having some issues with my nrf52 DK board, the jLink firmware seems to be buggy, I installed the latest available (160212) manually, but the j-link tool keeps bugging me...
SDK 9.0.0 sd s110
I want bootloader to store some persistent data at the APP DATA location. while going through the bootloader(dual_bank_ble_s110) source code, i noticed...
I have never worked with BLE devices before. Now I have a BLE project where I must be able to do he following:
I want to be able to pair/bond my BLE device to a smartphone...
chip N51822QFAACO
s110_nrf51822_5.2.1_softdevice.hex
keli 5
\nrf51_sdk_v4_4_2_33551\nrf51822\Board\pca10001\ble\ble_app_proximity\
works fine
nrf51_sdk_v5_2_0_39364...
Hello Everyone
I have designed my custom board using nrf51822 i have tested the votlage rating, on the VDD pins everything is fine (3v) but the real problem is my antenna...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
Hi,
I think there is the bug in SDK11 Spi slave protocol. After a msg is received from the SPI Master, I notice that the spi slave event always have the rx_amount and tx_amount...
Hi All,
I noticed these serialization FW with huge amounts of code in the makefile.
What is the core functional difference between any example with and without serialization...
