Hi everyone,
Could someone help me with the following use case?
Task description: I'm working on a firmware update procedure based on the smp_svr project. I'm trying to...
Hello,
I have made a project that was based on the nRF9151 Development Kit and it works great. I had to select the -ns configuration to get anything to ever build and now...
Hi,
I bought a new nrf52840 DK board as one ofthe original nrf board of my Qorvo QM33120WDK1 kit ( 2 x nrf52840 DK + QM33120W + QM33110W) J3 connector broke. Out of the...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
I am trying to set up UART communication between the nRF9160 and nRF52840 that are found in the Fanstel BLG840XE. Currently I am sending a test string of "abcd" from the nRF52840...
Hello! This is the third time I'm asking something about the same project, but I'm running into problems one after the other.
The current problem is this - the hogp object...
A question about the power saving modes PSM and eDRX. A device is mostly in deep sleep and wakes up cyclically for mobile communication. It is better: Completely disconnect...
In our project, two nRF51840 will communication with each other using BLE. One nRF51840 act as central and another nRF51840 with act as peripheral. The central nRF51840 will...
I have a couple of NRF51 parts. They're pretty common at hobbyist stores still. Recently I pulled out the NRF51 dongle, downloaded the recommended Segger Embedded Studio,...
I have managed to get working a BMW iDrive to act as a bluetooth mouse for my iPhone. To do this I used a CANBUS shield connected to an arduino NANO and an nRF51 BLE connected...
Hello,
Mesh SDK 4.0.0, PCA10040 x2
I want to develop next models:
Scan server: Waiting GET message with arguments, scan BLE beacons and reply STATUS message with results...
Dear Nordic Team:
Now I am doing a example test, with nRF52832 I want to use SPI master and SPI slave transtission.I have saw many demo example,but i dont know that which...
I don't know how it feels if you visit a page that takes six seconds to open.
Isn't the profit ability of the Chinese region enough to allow you to build a normal acceleration...
Hello,
I am working on nRF52832 chip using SDK 15.3.0 in segger embedded studio.
I implemented DFU in my application and it's working properly.
But my problem is when...
WHAT is missing from my profile which prevents me from opening a private ticket?
The location? when I type it in, your profile doesn't save it (it just ignores it).
Ubuntu18...
I have successfully compiled the GPS sample. I am trying to program the device using SES and only beign able to do it when the device is previously erased with NRF Connect...
Hello,
I am using nrf52840 to communicate with PAC 1710 sensor via TWI interface. The nrf52840 is the master device and the PAC chip is the slave device. Without SoftDevice...
I just updated to Segger 4.42a to follow the recommendation in the release notes for SDK v1.2.0
When I do a rebuild the AWS fota sample I get linker errors as shown below...
Hi,
I have a Laird Development Kit for the nRF52840 (DVK-BLL654PA-R2.0) which I want to program. Unfortunately Keil uVision and nRFgo Studio have problems with programming...
Hi all,
Greeting of the day....
Here I am getting an issue with TWI interface. That I am using to communicate with sensor module with NRF52840.
The SCL------> p0...
