I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud.
I already know my board IMEI (I got it by flashing the AT client sample and then...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
I am currently developing a firmware application on the nRF5340 where I need the device to function in dual role :
As a Bluetooth Mesh Node , communicating with other...
Hi, we are planning to use npm1300 for charging a battery, but we will have a limitation on the power supply (VBUS in npm1300 naming convention): the capability of making...
Hi everyone,
I've been testing SPIM with easyDMA, using nrf_drv_spi. I'd like to flush a 6-axis sensor FIFO in one SPI operation (31 samples * 12 bytes = 372 bytes) but...
Hi,
I am working with the ble_app_uart (central and peripheral) example and they already run fine. Now I discovered that some button actions are already defined on the...
Hello,
I have created the simple software usign NRF51DK to make the led blink for 5 times by using while loop
just to make the other part of my software
my aim of this...
hi，i have a question.
i set the advertise type to BLE_GAP_ADV_TYPE_ADV_NONCONN_IND MODE, and i add scan response data,but i can't see scan response data.Why?
Hi,
I would like to connect nrf8001 to a Renesas microcontroller but I could not find any documentation on how to proceed with this step. The only documentation I could...
The ADC module requires that the output impedance of the connected voltage source be 1kohm or less (section 31.1.3 of RM).
Does the same restriction apply for the LPCOMP...
Im having some issues with my nrf52 DK board, the jLink firmware seems to be buggy, I installed the latest available (160212) manually, but the j-link tool keeps bugging me...
SDK 9.0.0 sd s110
I want bootloader to store some persistent data at the APP DATA location. while going through the bootloader(dual_bank_ble_s110) source code, i noticed...
I have never worked with BLE devices before. Now I have a BLE project where I must be able to do he following:
I want to be able to pair/bond my BLE device to a smartphone...
chip N51822QFAACO
s110_nrf51822_5.2.1_softdevice.hex
keli 5
\nrf51_sdk_v4_4_2_33551\nrf51822\Board\pca10001\ble\ble_app_proximity\
works fine
nrf51_sdk_v5_2_0_39364...
Hello Everyone
I have designed my custom board using nrf51822 i have tested the votlage rating, on the VDD pins everything is fine (3v) but the real problem is my antenna...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
Hi,
I think there is the bug in SDK11 Spi slave protocol. After a msg is received from the SPI Master, I notice that the spi slave event always have the rx_amount and tx_amount...
