Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I tried to connect my nrF52 DK board to various devices, via USB. None of the devices was able to see the board.
In addition, nrF Connect / Studio wouldn't see the board...
Hello,
I am trying to understand how to use an external button. In the first stage I am trying to replace the functionality of button0 on the DK with a GPIO.
I took the...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). I'm working with the ble_peripheral example...
Hi, We are using the nRF52840 in a 3V battery powered product. We have an on board 1.8V LDO regulator that supplies Vdd and Vdd_IO. We have a problem with the NFC antenna...
Dear all
I currently have a single nRF52832 SoC (custom PCB) transferring data to a single nRF51 dongle via BLE, which in turn passes the data to my PC via UART. I have...
Hi everybody,
I'm having a problem with the advertising function of the SoftDevice.
When the application starts advertising the function "sd_ble_gap_adv_start()" returns...
Hello,
We are currently looking for a way to test nRF52804 on our board with CMW500. From R&W video clip, they tested Nordic eval. board with USB connection. How do I make...
I’m interesting particularly nRF52832 and nRF52840 (with and without bootloader)
So looking at flash layout with bootloader :
is the section ‘Application data’ available...
i want to send string over eddystone tlm...and wish to use temperature part for this...so how can i display character string instead of temperature in eddystone TLM..please...
Hi, I am trying to use the iOS nRFMeshProvision SDK to create a iOS mobile application. I am trying to get the composition data but access layer always times out and gives...
Hi, I am new to Dev Zone. I am writing debounce logic and I am wondering if a button can have an interrupt set when the GPIOTE sense a HITOLO transition to fire the first...
Hello, I'm currently developing BLE_SCANNER(GATEWAY) for asset tracking or management.
My scan environment is,
[Our device -- same UUID]
The number of our beacons...
Hello. I have the same problem with https://devzone.nordicsemi.com/f/nordic-q-a/54373/uart-logging-backend-hangs-in-nrf_bootloader_app_start/220132
But this thread was stuck...
I'm trying to register a handler to determine when a system event occurs?
Previously on older design kits, I used softdevice_sys_evt_handler_set(......) to register the...
