It flashes with sucess
C:\Users\vasco>openocd -f interface/stlink.cfg -f target/nrf52.cfg -c "program \"C:/Users/vasco/OneDrive/Ambiente de Trabalho/zephyr.hex\" verify...
Hi Team,
We are developing on a custom board with an nRF54L15 (Raytac Module with NRF54L15_xxAA_ENGB) and are unable to provision a pre-generated secp256r1 private key into...
Hi, I want to run Bluetooth Mesh Light example on nrf54h20 chip.
At the beginning I prepared devboard with this tutorial: https://docs.nordicsemi.com/bundle/ncs-latest/page...
Hello,
I am trying to build a firmware for the nRF5340 on the Thingy91:x. The firmware should use the external flash for the secondary Image and is using the chained bootload...
Dear Nordic Semiconductor Team and Community Members,
I am currently working on an nRF54L05 project where I aim to use only the primary slot in MCUboot due to memory constraints...
Is there any documentation around the process to disable the Debug Access Port on a nRF54L device in software (not nrfutil)?
The nRF52840 has this nice documentation page...
SDK: nRF Connect SDK v3.0.2
DK: nRF54L15-DK
Sample: spi_flash
default:
mspi-max-frequency = < DT_FREQ_M ( 8 )>;
If I change it to 32, it will printf these...
Hi：
1： NRF52832 How to set up the TX transmission power.
ble_app_hrs ：didn't see set TX transmission powe
2、NRF52832 ：How much is NRF52 maximum rate, how to set
THS...
What are the certifications required for Australia? My device has FCC and CE certifications, are these enough to allow someone to import my device? We are both really unsure...
I'm using the nRF51822 DK + SDK10.0.0 + s110. I'm going to create a system where I do an SPI read from two sensors every 6ms. From these sensors I will get 20B each over SPI...
I'm writing a program sending die temperature data through BLE. I'm trying to combine the nrf51822 Heart Rate Monitor example and the nrf6310 Temperature example. Both examples...
Hello,
I have connected a SX1272 module to a nRF51 Development Kit using the Arduino connectors. Anybody written a sample app to get me going?
There is a SX1276 Ping Pong...
Hi all,
We have implemented the wireless mouse example on some custom hardware and it works great. We need to do something a little different however, and send absolute...
I can run peripheral examples in SDK folder like GPIO, Timer, Scheduler ...
but when I want to Add somethings like GPIO to peripheral_UART_ble or timer or scheduler It didn...
Hi Nordic Community,
I am using the nRF51822 to receive a data stream from the SPIS module and transfer the data directly to a phone over BLE using the S130 softdevice...
This is a follow-up question to devzone.nordicsemi.com/.../
I am using SDK_11 s130 on nRF51-dk.
I discovered that on nRF-UART Android app, notifications are not enabled...
I managed to enable pairing without bonding on ble_app_uart by porting peer manager over from ble_app_gls. I am using SDK11 s130 on nRF51-dk.
I observed some strange behavior...
Hi Nordic's community,
I have an issue when writing uint32_t to a characteristic, i don't understand when i write uint16_t or uin8_t, it works ! but don't when i send an...
Hi,
I would like to add single bank signed DFU support to my project (running on nrf51822AC - 256kb version).
In SDK 10, there was an experimental bootloader with a nice...
Hi,
I want to transmit adv. data AES encrypted everytime. The Basic requirement is to do Encryption with Stream Cipher (Counter Mode) so i want to know when and where to...
Hi,
I am trying to get bonding to work in both iOS and Android versions.
As per the suggestion in : devzone.nordicsemi.com/.../ I used
attr_md.read_perm.sm=1;
attr_md...
I wanted to do pairing without bonding with ble_app_gls s130 SDK_11. I tried setting SEC_PARAM_BOND to 0. However, this caused the device to stop advertising. What is a better...
