Hello dear fellow developers,
I am solving the problem of how to add another peripheral to the project.
I would like to know a universal procedure for adding any peripheral...
Hi nordic： What is the peak current of NRF9151? The relevant parameter cannot be found in the datasheet, while it is available for NRF9160.
Best Regards
JERMI.JIN
I'm using the nRF52840-DK part number 1490-1072-ND I ordered last week. In both nRF Connect for Desktop and the VS code extension the device wasn't able to detect. Tried two...
Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
In the documentation for the secure bootloader, it's mentioned that the provisioning data gets stored in OTP memory for some chips (e.g. nRF5340). Is there a way to know what...
Hi:
I don't receive any messages in the console during any of the exercises in Lesson 3 and Lesson 4 of the nRF Connect SDK Fundamentals.
No errors occurred during the...
Device Overview
We have developed a smart wearable that sends notifications to our mobile application over BLE. Under normal conditions, the device alternates sensor...
I have an application that bonds to mobile devices and encrypts the connection on both Android and iOS. What I am noticing though, is that after each time I use the DFU to...
I want to stop advertising for 8 hours
but when I use
sd_ble_gap_adv_stop();
sd_ble_gap_connect_cancel();
It starts advertising after 1 or 2 secends again.
I think...
Hi,
I followed the tutorials shown below:
infocenter.nordicsemi.com/index.jsp
I downloaded SDK v11.0 and loaded S130 SoftDevice on my nRF51 DK. I use Keil uVision 5...
I am working on a bootloader for a client. I’ve been looking at the DFU example that Nordic has. The BLE version of the DFU needs to have the special format using the “nrfutil...
hi:
I use bootloader example of sdk 9.0.0 ,most cases worked fine, but I got gatt error sometime when I begin DFU. I had changed the dual_bank_ble_s110 into sigle_bank_ble_s110...
The nRF51 reference manual says that GPIO PIN_CNF registers are retained registers and that "a retained register is a register that will retain its value in system OFF mode...
Hi,
I'm trying to add second service on the fly, while SD running. After adding it, I'm trying to send service changed notification, but it don't work. Below is code used...
Hello.
I test nrf51822 central and peripheral.
I want to change radio channel frequency about nrf51822.
I test source code as below.
nRF51_SDK_10.0.0_dc26b5e\examples...
there is an error on softdevice on src\ll_adv.c on line of 659 . what is the reason?
this is my adv init
#define DEVICE_NAME "navid" /**< Name of device. Will be included...
hi
I want to know whether we require MCU for enabling "Enhanced shock burst mode " or when we set the CE pin to high for making RX that time automatically this will enable...
Hi everyone,
I am using the nRF51822, I have an issue of programming the bootloader.
It is said that the flash is not erased. But I just did an erase all before programming...
Hello,
I have two questions regarding nRF52832 ADC, which are not documented :
what is the precision / tolerance of the internal 0.6V reference?
what is...
hello there,
I use currently 'ble_app_hids_keyboard_s132_spi_pca10040' app of SDK11 for my nrf52832_xxaa device on 'IAR' IDE. It utilizes sofdevise s132. I do not use the...
Hi
I'm encountering a problem in UART communication with nrf51422 on a custom board over an FTDI USB-serial converter ic.
When I send a string > 40 chars from the terminal...
