Hello, I hope you are well.
I created a new driver for an i2c accelerometer with 2 gpio interrupts, but it does not build properly. When calling `static const struct device...
Hello everyone,
I'm working in a ble project that use uart interface. When I sent string data in nrf connect app, the uart_event_handle is not called.
I started my project...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
nrf5340DK
NCS 3.0.0
if I use sample zephyr/samples/boards/nordic/system_off it works fine and i can wake from sw0 press. but if i move the sys_poweroff() call int a...
Hi Team,
Recently we did a network related testing for our CL5G modem (nrf9160) and observed a problem, in this test we used a nmap tool, this tool will search for open...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
In my test, with the same configuration, ANTWARE II always searches much faster than nRF51422 software.
For example. I have Master channel and Slave channel set up at 4Hz...
The test code:
#include "nrf51.h"
int main(void) {
NRF_CLOCK->LFCLKSRC = 0UL; // Internal 32kHz RC
// Start the 32 kHz clock, and wait for the start up to complete...
Hi,
I have downloaded "mastercontrolpanel.3.7.1.8567.x86.msi" and try to install on windows xp of my intel core2 laptap. But it failed with prompt like "not a valid windows...
This question devzone.nordicsemi.com/.../ reports the fact that the driver cannot be used twice without manually pin reseting teh BLE dongle.
But there is another problem...
Hi Team,
I am using nRF51 DK as packet sniffer to sniff packets between Mobile and other device.
Why it captures only advertising related packets?
After successful connection...
Hi there,
If I try to store a global variable in flash I can't store it. But when I declare this variable in the main function I can store it in flash. Can someone tell...
Hello all,
I saw their was a new update for the nRF518-SDK and I was wondering how I should update this in Keil. Is this just a simple replace folder? Replacing:
...
I inherited an ANT/BLE nRF51422 project a couple of weeks ago.
It used SDK v6.1.0 and S310 SoftDevice v1.0.0
At the time, I'm sure that the SoftDevice download said...
I'm attempting to troubleshoot problems between dev teams. One team is having some issues & I notice that their binary is slightly larger when built from exactly the same...
I am trying to use the laird BL620 module not for the smartBasic, but to run my own firmware.
I have just set it up, connected to my old segger JLink debugger.
In Keil I...
Press the Connect button on the Smart ponaep NRF Uart V2.0 recognizes the page reongil signal
Disconnect state, allow to boil for your smartphone to wait about 20 minutes...
I am pretty new to the nRF51822 in the firmware side. I have been doing hardware design for many years but need a little help getting started with firmware.
Does anyone...
When the bootloader in SDK 8.0.0 checks whether the application is valid, it only computes the CRC for the application if the CRC in the bootloader settings for that bank...
Hi,
I try to make characteristic broadcasting through advertisement data packets.
Added these codes below, but no yet work. Is there any example for this work ?
char_md...
