Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hi all,
recently I tried sd8.0 and i used the example "ble_app_hrs".
the strange thing is in my phone i can see device advertising but cannot connect to it successfully...
I tried to use this example with a nRF51422 and the board of N5 Starter Kit of Dynastream. I adjust all to make it works fine: custom_board and so on.. And I used the Soft...
From SDK 7.2, we have the following definitions:
components\drivers_nrf\pstorage\config\pstorage_platform.h
typedef uint16_t pstorage_size_t; /** Size of length and...
There was something in the webcast yesterday about a Nordic nRF52 roadshow/tech tour/worldwide series of events.
I hunted around the nordicsemi site but didn't find anything...
hi,
i am working on ble project where i am trying to develop a project with master(mobile phone)-bridge(acting as master and slave,nrf board)-slave(nrf board) .i use the...
Hi,
I would like to save the most energy when going to sleep mode. In particular, I want to turn off all modules except the RTC timer.
So, after shutting down the radio...
Hi,
How could i implement Just work pairing method in my "ble central and peripheral" example. I modified project to suit my need, and everything works fine, untill i try...
I am working on a ble project ,'ble_central_and_peripheral",s130.In this project the device acts as master and slave. It connects to the slave only if the address is predefined...
I may be missing something. I am trying to generate a square wave from a GPIO pin in a BLE application (SoftDevice 8.0). I tried libraries (nrf_pwm.c and nrf_pwm.h) in this...
Why does the nRF52 only have +4dB output when most competitor chips are atleast +6dB (some up to +10dB). I understand that the RX has been improved by 3dB for a better overall...
Is there a way to know that there is no more data being received via UART?
One solution is, of course, to start a timer every time a byte is received via uart_evt_handler...
I am using read characteristic to read data from from a characteristic. The characteristics range from 2 bytes to 32 bytes in length. The time to read the data using IOS,...
For those of us who were not invited to Norway to try the nRF52 over the next two days....
When and how can we get our hands on a nRF52 development kit?
For example, ble_advdata_set() wants to insert company identifier and a "00" in the last byte of the response packet. Are these required, and if not, how to use the ble_advdata_set...
