Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Iam using LPCOMP for my project i would like ot know where the header files are available to download, iam getting the error
....\main.c(33): error: #5: cannot open source...
Why isn't the nRF52 ADC internal reference voltage included in the electrical characteristics on the SAADC in the Product Specification? Knowing what voltage the ADC is referencing...
The table on:
infocenter.nordicsemi.com/.../gpio.html
specifies: Iol,hdh = max 15 mA for Vdd >= 2.7V.
The graph lower on the page (Figure 6. Max sink current vs Voltage...
Hi Nordic,
when 51822 communicate with an app,is the best way to use different services and characters
to achieve different passageway or use a self expand protocol on...
dear all
I have two same 51 822 device with same program, one is normal, the other can't be connected even re-power manually .The two all can be found by nrf master control...
Hi,
I have been able to use SAADC to measure temperature, but my code does not behave in the way I expect it to!
In the config file I have the following settings set:...
Good day,
I try to add inline assembler like this:
asm("POP {R12,PC}");
but I have an error:
Error[Og006]: Error in inline assembly: "Error[401]: Operand syntax...
Hi!
I'm currently developing a driver to communicate with a sensor via I2C using the Nordic's nrf_drv_twi library. I based my code on the twi_sensor example, but since...
We are in process of identifying the right hardware for our project and considering nrf52832 as the core processor. For our requirements, we need to use external serial NOR...
Hi,
I was trying to complie my code but the Keil is giving this error, which I am pretty sure is about the recent update that I have downloaded. I am using nRF51822xxAA...
hi i am using nrf51 development kit. i have gone through nordic development zone tutorial to use Eclipse IDE. build was successful it is creating release folder in which i...
We are interfacing serial flash using SPI interface and use nordic nrf52 nrf_drv_spi.c as the library.
We have taken a look at nrf_drv_spi.c, and it seems in the api nrf_drv_spi_transfer...
I am using Nordic nRF51 Development Kit with SoftDevice_130_2.0.0.I tried to run the SDK 11.0.0's example "examples\ble_peripheral\ble_app_gls\pca10028\ser_s130_spi" from...
As Nordic newsletter, s132 v3.0.0 softDevice have been released, I have a question that: if I want to use new feature in s132 v3.0.0 like DLE or privacy, does Nordic need...
I am trying the tutorial Radio Notification and was following the patch from Ble_radio_notification wont compile . The radio notification init comes right after the ble enabling...
