I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
In the spec TA is specified with a max of 85°C
I assume that this is the Max Ambient temperature and that the die temperature may be higher
Is my assumption correct?
may...
Still trying to get anything ta all to work on the nRF52-DK
I erased the chip
I flashed the soft device "soft_device_s132_v3.3.3" to address 0 and verified
built...
Hi!
We are having problems with pairing & bonding procedures with iOS devices.
On the peripheral side we are using a nrf51822 BLE module on which we are testing pairing...
Hi all,
2 days before we bought nrf52832 board.
in new board i can able to execute all peripheral example ( LED BLINK,button,uart,timer..)which doesnt need softdevice...
I'm trying to setup the RTC in the nRF52 to count with a resolution of 1mS. As the count has only a 24 bit value, I wish to clear the count every hour to start again.
There...
Hi all,
I'm having a error on my code, and wanted to understand it better. I'm using a custom board with a Rev.3 CTAA chip, 256k Flash and 16k Ram. I have BLE initialized...
I measured my Nrf51822 current:
when my VCC is 3.0v ~ 3.3v
my current is 0.16 mA.
when my VCC is 2.6v ~ 2.8v
my current is 1.5 mA (why?)
when my VCC is lower than 2...
I have issue with nrf51 booting, i noticed that sometimes when i plug the power to (VDD and GND) the system dosent turn on at al.
1 - how does the system the whole system...
amigos de habla hispana estoy comenzando con este circuito.
mi duda es cual compilador utilizo para crear un simple led blink..
tienen algun tutorial en que me puedan a...
Hi.
I am using the nRF52 Preview Dev. Kit to send data over multiple channels by
setting the NRF_RADIO->FREQUENCY register to the desired frequency value.
To make it work...
Hi,
I am trying to measure the temperature using sht21 sensor with nrf51822. I am using TWI to do this. When I try to send a data to the sensor the application cannot do...
Using the nRF52832 and SoftDevice s132.
If the application code disables the SoftDevice, then the application CAN erase UICR memory in the nRF52832 device.
The question...
I control a module over UART using app_uart_fifo. This module is controlled from nRF host by commands to perform things. This generally works fine but however, sometimes when...
