Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
As a summary (described fully below) I have loaded the ble_app_hrs example onto my device and its not working right as LEDs that should light up don't and the program...
In some of the Nordic examples I found by viewing the raw advertisements that the company ID is set to Nordic's ID (0x0059). In order to communicate with Apple devices (e...
Hi Nordic Support community,
I asking regarding LNP, Location and Navigation Profile, if it's possible to on top of nordic products? If so like which ones ?
There's barely...
Reading the documentation Address config it is clear how to use RXADDRESSES, could you please explain how to use TXADDRESS ?
As of TXADDRESS there are 3 bits available...
I am having trouble with using shockburst (based on microesb from github) after disabling S132.
When I use microesb with no SD, i just do nrf_drv_clock_init(), start lfclk...
Hi,
I am new to Nordic development platform and am exploring ways to develop software applications to communicate over bluetooth. Presently, I am working with NRF51422...
Hi, I have a problem about gpiote interrrupt.I have set two ports to detect the external interrupt(low to high). If only one port get active ,it works fine. But if one port...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi I am beginner to nordic ble. I have four nrf528** development kit. I am just trying demo heart rate example with android toolbox app. Suddenly one of my nrf devlopment...
I am currently using MBR, and know the general interrupt latency due to MBR + SD from Table 26. But I cannot understand how you arrived at those numbers. IF this table was...
Hello All
Hi, I use nRF52832 with SDK11 Version. But SDK11 didn't provide any CSCS central example. Anybody wrote ble_cscs_c.c for BLE / Cycling Speed and Cadence Service...
Yo men,
I study this web
infocenter.nordicsemi.com/index.jsp
Experimental: Flash Storage
I have 100 bytes data need to read/write/store.
So I think even this is Experimental...
Hi guys,
I compile a provided example with my nRF51_DK and it works well. But when I re-run the program, it will be block in function "sd_rpc_open()". The only solution is...
@Vidar I'm facing a issue with Debugging using Eclipse, following the steps you mentioned in the tutorial "Development with GCC and Eclipse".
Made the below configuration...
