We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello,
i have seen here a extended version of Spi-Master driver:
devzone.nordicsemi.com/.../a00006.html
With funktions like:
-spi_master_send_recv();
spi_master_get_state...
I'm using the reference design for the WLCSP nRF51822 package, and I noticed that there are 2 pins (G3 and G4) that are listed as N.C. (No Connection) in the product specification...
Hi,
I am upgrading SDK from 5.2.0 to 6.0.0 working with SoftDevice 7 and I am facing a problem in relation with ANCS.
When I am pairing the phone (IOS 7) the first time...
Hi.
I have been trying to store data in flash by using pstorage.
What's the difference between pstorage_store and pstorage_update?
At the first time, I can save data...
Hi,
Is nRF51822 / S110 capable of simultaneously being in peripheral (connected slave) and broadcaster (broadcasting non-connectable ads) mode? The datasheet says both...
Hi,
I need to write data in to flash memory of the nRF51822 device.
I have tried to write data. When i checked memory address where i wrote data i could find that the...
In the nRF8001, after executing the command "ReadDynamicData"... I receive basically a bitstream with many bytes. The idea is to store it in order to be able to, later on...
I'm trying to write a flash buffer but am hitting a vexing error. To initialise the flash buffer (or rather a test initialisation which will hopefully become the flash buffer...
Hi
I would like to interface nRF8001 with a BeagleBone Black (BBB) an ARM cortex-A8 [1].
BBB has a SPI inteface and can support interrupt line input, and its running Linux...
I have an nRF51822 that I would like to be able to issue a soft-reset command under certain circumstances. I'm not using a softdevice in this version of code, so the other...
Hi,
I'm using pstorage, but found some problem. sd_flash_page_erase will not trigger system event after the operation is complete.
In my code, I registered the system...
Are you supposed to be able to nest critical regions using CRITICAL_REGION_ENTER and CRITICAL_REGION_EXIT? Here I mean you have a function which uses a critical region to...
I'm trying to run bootloader from nRF SDKv6 with SDv7 in gcc.
On our custom board, it runs, but does not advertise (sd_ble_gap_adv_start gets called and does not return...
