Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
How many whitelists do nrf51822 support?
I found is can be settting in ble_gap.h
#define BLE_GAP_WHITELIST_ADDR_MAX_COUNT (8)
#define BLE_GAP_WHITELIST_IRK_MAX_COUNT...
I'm working on a project that involves an nRF8001-based device as a Bluetooth Smart slave, in combination with master-side software running on an iPhone.
When the devices...
Hello
I have written some code to write the nrf51822 via SWD. It all works, but I would like to make it faster.
I am currently writing one word at a time. If I read...
Hello dear friends,
I'm trying to bring up a Raytac module for the first time. I was able to program S110 7.1 and I'm using the Beacon example found in the SDK 6.1
But...
Is there a similar way tot get the radio's MAC address when using Gazell only (no BLE)?
In SoftDevice there is a "sd_ble_gap_address_get()" function call.
Hello All,
I'm trying to program a NRF51822 module for the first time. I'm using the Jlink for ARM from IAR which is segger rebranded. It supports JTAG and SWD.
We got...
Hi,
I am trying to obtain a 10khz PWM (50%) on an output using Timer2 (see code below). It is working fine up to around 500Hz (2msec), above that (1kHz) I am getting only...
I would like to develop an application with nRF8001 DevKit. The master emulator of this kit is an USB Dongle and it is originally meant for PC connection. My final goal for...
Hi all,
Problem: Second harmonic with nrf905.
I used nRF905 and exact recommended design&layout in the datasheet. Now, it is said that there are 2. order harmonics ...
It seems that the all the msc_inline_*.png files are missing from the SDK 6.1.0 documentation directory.
For example:
file:///C:/Nordic%20Semiconductor/nRF51%20SDK_v6...
Hi,
I use NRF51822 as a transmitter in "gazelle mode" so no soft-device is enabled. At the other end I use NRF24LE01 as a receiver. In order to see what is going on in...
Hi All.
I made a nRF51822 based PCB with SWD header but I don't have any J-Link lite to load Firmware.
I have a nRF51822 Eval Kit. Is there any way to use the J-Link of...
Hi,
I am using nRF51822 and I compiled and loaded uart example code. Also i used nRF toolbox android application on samsung s5 with android 4.4.2.I am using sofdevice 6...
