I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Hi guys,
I can get a rand number use the API:err_code = sd_rand_application_vector_get(buf, bytes_available); but the question is that How can I get a rand number just...
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
I have a strange problem with pstorage function with nrf51822 with s110 v6.
I need to use nrf_delay ( about 1 second long ) after store and before read.
This is the source...
Hi,
I am using softdevice 6.0.0 and ble_app_hrs example in keil on a custom nRF51822 board. Compilation goes fine but when I try to debug I notice that the firmware seems...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
Hi
I am using S110 v6.0.0
I have written an app that has a single service and I then register the same characteristics until it fails. The properties is 0xA (read/write...
Hi,
The nRFgo Studio v1.16.1 will up side down the contents of old profile XML that created by v1.16.0 or v1.15.x.
And use the new generated services.c and services...
Hi,
So I'm using a BT 4.0 dongle (Laird BT820) to set up a LE notification loop with the nrf8001 (RedBearLab shield on Arduino) using gatttool on Ubuntu 12.04. This works...
I've used the nRF8001 on several projects with good success, so I'm generally familiar with the chip's operation. But I'm seeing an issue on a new (custom) board that I'm...
We are currently researching which BLE chip vendor to use so this question is directed at Nordic personnel familiar with the S110 stack's capabilities.
In a situation where...
I would like to use the nRF51822 evaluation kit as an observer to detect beacons and take action based up the RSSI value. I can't seem to find any source code for S120 or...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi,
Repro, using the Nordic hid-profile + iOS 7.1.1:
Pair the nrf51822 based hid device via the iOS bluetooth menu.
Turn off nrf-device.
Boot up the nrf-device...
I want use pstorage write and erase flash,as shown below:
//pstorage_init(); // device_manager_init have been called,so there's no need to call
err_code = pstorage_register...
