Hi Nordic：
We are currently testing Zigbee on the nRF54L15 platform using the Zigbee R23-add-on-V1.0.0 SDK. It has been observed that when a low-power node disconnects from...
Hello, I am using ISP1907 which has NRF52833. I get the IQ data and configuration from serial as: DF_BEGIN ['IQ', 0, 0, 11, -9, -213] ['IQ', 1, 8, 11, -209, 23] ['IQ', 2,...
I have 2x Power Profiler Kit II up and running using the Power Profiler app - started twice and with separate PPK2 instances selected, as described in another support post...
Hi, I am running openthread on the NRF54l15 DK. Whenever I am debugging and hit the breakpoint or pause the program, then on resumption my app crashes. How Can I debug while...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
Hi,
Can the value of NRF_RTC1->COUNTER be read safely from the main loop without first stopping the RTC or temporarily disabling the RTC1 interrupt etc? (nRF51822 or nRF51922...
I used the nRF51822 Evaluation kit and flashed the BLE_proximity example on to the PCA100001 board.
In the master control panel the USB dongle measured -46 dBm(Nordic_prox...
Hi all,
what if I want a sensor network in my house with BLE. Can I just install, for example, 16 nodes in my house and connect to all of them with one iPhone? Or would...
Hello,
I am currently using nRF24L01P with TI CC2591 in my RF module product.
I have a doubt that need your help to clarify.
Does the antenna impedance given in the...
We've been trying to user the AES hardware module in ECB mode.
To do that we used the sd_ecb_block_encrypt function.
Is this hardware accelerated? Based on power consumption...
Hello,
I would like to know if I could interface the nRF51822 with an Arduino Mega Board. Could you give me some advices to do that?
Thanks for your help
Hi,
i need to use a watchdog in my application. I read that i can use the build in one, but i thing my configuration or the usage of the watchdog is wrong.
here is my config...
Hi guys,
I am getting started with your nRF51822 dev Kit. I got the nRFGo Starter Kit (nRF6310 Rev 1.4 mother board) as well. Most of the examples work as expected. But...
Hello,
I'm trying to do a millisecond counter using app_timer but the callback is never called. I think I have missunderstood how it works.
I've tried using the app_timer...
Hi,
Im trying to send 20 packages of 30bytes each as fast as possible, so I created the following loop:
for( pack=0; pack<20; pack++)
{
w_tx_payload_noack(30, MegaBuffer...
Hi all,
I have a custom board with the Nrf51822 BLE chip and it works in broadcasting mode without connection only. Basically it sends the advertising data on an established...
Hi
I have some problems about using your Master Emulator API. I want to write a dynamic link library with C++, but I don’t know how to invoke the MasterEmulator.dll.
The...
I'd like to use LPCOMP. I'd like to get rid of the 12K pulldown on SWDIO.
I can tell from PCN-082 that QFAA CA and C0, as well as QFAB AA and A0, will let me do that. ...
