Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi all,
i am having issues with the mKit and current consumption.
Just an FYI to measure consumption i am placing the mKIT in series with a shunt resistor and measuring...
I've spend some time figuring out where the application code should start for the S130 . Table 11 in the SoftDevice Specification v0.5 document indicates that it is at 0x00020000...
I check the function spec that we can use use 32kHz RC as LFCLK, so I have no external 32k crystal connected with XL1/XL2 on my board.
I have set
NRF_CLOCK->LFCLKSRC =...
Hi,all:
I have a question.
could I use android/ios APP to connect several BLE devices at the same time?
because I want to use andriod APP to control all of the BLE...
I'm trying to write a central BLE with the dongle(PCA1000) using s120.
I programmed s120 sd ver 1.0 the same way as the s110 with the nrFGO ver 1.17.
However i keep getting...
Hi all,
I need to change the device name frequently to show button status.
So remote device can see button status without connecting to device.
Is there any way to...
Hi guys,
i have a service with more characteristics and more states. Not every characteristic should be available in each state. Thus there are services which are just...
Using the S120 soft-device in the Central role, there does not appear to be an
example or documentation describing how to scan for a 128 bit UUID service.
Has anyone tried...
Apparently there is some limitation on length of the paths with Keil. The paths are specified under "Options for Target" --> C/C++ --> "Include Paths". Due to this limitation...
I downloaded the nrfgo Sdk for the nrf24lu and nrf24le. In the projects folder there are several examples, two of which are of interest. The first is entitled "bootloader_32K...
Hi
I'm having a strange behaviour when using the TWI HW peripheral for reading from an I2C device. My application tries to read one byte from a register in a I2C device...
Hi,
I'm done with the hardware interface of my current project.
Right now I have a service running with a custom UUID, by writting this characterisitics you have access...
Hi,
I'm having the purpose to use nRF51422 /ANT to connect a relatively data hungry ANT device. The nRf51422 specs expose three programmatically available data rates : 250...
Hi,
I've written a nRF51 SWD-JTAG programmer.
I want to enable it to check for minimum softdevice version and error out if a too-old softdevice is found.
It is easy...
