hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
I try to open ANT+ channel and make sure the status is searching or tracking,
but if I use pstorage to update flash in the same time,
It will response timeout...
We are developing a keyboard for smart phone or plant and what to make different surpport for different device.
So can I make difference from ios device and Android device...
Please indicate me if there is a data port on nRF8002 after you burn out OTP, Can I use this I'c for data transmission. Please indicate communication port for this chip. Also...
Hi,
I'm testing ble_app_proximity example (...\Nordic\nrf51822\Board\nrf6310\s110\ble_app_proximity). I'm using Master Control Panel Android app version 2.0.3 and Nexus...
I'm using S110.
I have a characteristic that is writable from phone client. However, the characteristic has lower and upper limits (an acceptable range) for the application...
Hi experts,
I'm trying to bond device between my android phone and the Nordidc51822(S110 v7.0). but I found that it's very difficult to achieve this function. Is there...
Hello,
I'm using nordic 8001 chip within a custom board.
Everything is working but rarely, at random moments, I'm receiving packets with 255 length. I attached a print...
1,I use nrfgo studio and can download softdevice ,it is OK.
2,I use the s110 example,it runs ok too.
3,I modify something from the example ,and click debug(keil),but it...
1,I use nrfgo studio and can download softdevice ,it is OK.
2,I use the s110 example,it runs ok too.
3,I modify something from the example ,and click debug(keil),but it...
I would like to be able to do a sanity check on the CHIP ID.
The Product specification states:
"No ID will violate the rules specified in section 6.4.3.2"
Section 6...
I am finding it difficult to figure out what is the minimum toolchain requirement to get started developing using the nRF24LE / U.
Is Kiel the only compiler ? Can SDCC...
Hi,
I have nRF51822 DK with (s110_nrf51822_7.0.0, nRF51 SDK_v6.1.0.0) and when i try to run the project in IAR 7.20.2 i receive an error.
2 ) My icf file...
Hi!
I have bought the nrf51822 EV KIT and it came with 5 extra nrf51822 modules but them without a board. I have researched a little and I found that I need the Segger...
Hi,
We're using an off the shelf module with a trace antenna that can't be modified.
Measured the module once assembled, and due to surrounding plastic materials, the...
