I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hello
I created the out of tree sample sensor application with SDK 2.6.2 and it built just fine However it builds only when it is inside the sdk that was pulled when I selected...
Hey everyone. I am having an issue reading the WHO_AM_I register from the stm lsm6dsv16x. I am using the spi1 configuration as shown in the academy classes. I have very short...
I am using an nRF52840 USB dongle to sniff some Zigbee packets for a product I am developing. I am trying to use Wireshark to decode the messages shared. I followed the steps...
HI,
I have created a msec Timer with the counter.h library of nRF Connect SDK. I am looking for a function that resets the timer in some cases.
According to Nordic Semiconductor...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
Im trying to write software on a custom PCB based on the 5340/7002.
A single device/single config/single endpoint (in and out) works great.
However if I try and do...
Hi,
I'm using nRF9160DK with SDKs v3.0.0
I am trying to use A-GPS with nRFCloud REST. I used the location example and it works correctly. The documentation states that...
Hi, I am using the nrf54L15DK to take some current measurements. I am using the PPk2, connected to P6 on the DK, supplying 3V, and have the USB on the DK connected. With a...
Reference states a +/- 3% tolerance, which is rather high. 1. Do any of the reference voltages exhibit a better tolerance? 2. Is it possible to roughly model the tolerance...
Hello Nordic team,
After many hours I have not been able to get socket dispatching working with Zephyrs MQTT client, and I am not sure how to proceed.
First of all I would...
Hi, We’re trying to develop a way to create fully self-contained repositories that include:
-the toolchain
-the entire SDK
-the necessary tools (for example, flashing...
Hello,
Hopefully this will be a quick(ish) one since I think I found the answer, but just need confirmation.
To preface (My setup):
nRF9151DK
Modem firmware: mfw_nrf91x1_2...
Hi,
I am currently working on a two way communication between an nrf52840 thread host and an nrf52840 thread client over coap. I have nrf connect sdk version 2.9.0 in both...
Hello,
I just got nRF54L15 DK and Im getting this error when flashing it:
Im running on a mac, have NRF Connect installed along the command line and 2.8-2.9 sdk...
I wanted to know if this program starts sending advertisements using the Coded PHY OR if it starts advertising in the normal advertising channels using the normal 1Meg output...
