Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
i am using the nrf51822 with softdevice s110. In the spec i read that the contoller works as well with an external 32khz reference which i want to use. The oszillator...
hello everyone,
i use nrf51822 and i want to use one switch that wakeup the module from sleep mode. so can i connect switch to gpio of nrf51822 module. if yes than which...
I'm a newbie so bare with me. I had this code running, saved it, and started another project. I tried not to touch any of the files I had running with the example below, but...
application note nAN-034 describes two alternatives for production testing an application using the nRF51822. One method is using a commercial tester (MT8852) and the other...
I need to send data PIR motion detector sensor to the master controller in my motion detector network.
Can I get away with just one of the nrf51 chips and my PIR sensor...
We're trying to decide at what voltage we should run our nRF51822 on the next revision of our board. To date we've been doing fine at 1.8V. The current drawn on a 3.7V lithium...
hi, i made ble app including bootloader using nRF51822 (s110), sdk 6.1.0
when i use sd_nvic_SystemReset() function in app, it erase app's pstorage.
But i want to preserve...
Hi,
I use S120 as central device and I need to handle multiple connections.
However S120 works quite unclear to me.
If S120 doesn't reply to BLE_GAP_EVT_CONN_PARAM_UPDATE_REQUEST...
Hello ,
I am trying to develop an application using the S130 soft device using Keil MDK v5 Lite. I have came to know that it is not possible to generate a code size greater...
I've run into a problem using the provided spi master code.
I get the following error message from Keil
spi_master.c(381): error: #1059-D: an entity with an internal...
Hi
I want to run the ble_proximity template on micro blend (Readbear lab). But I can't make it to work. I have uploaded the code to the board and using the nRF Proximity...
Hi all, I have followed the steps described
https://devzone.nordicsemi.com/question/14780/nrf51822-development-kit-without-nrfgo-starter-kit/
with the alternative power...
Hi,
I have successfully implemented a HID keyboard, using the nRF8001 and arduino sdk 0.9.1 ported to a microchip PIC18F controller. Connecting to iPhone iOS7.1.2
Everything...
hello,
please find main.c file of code and how to add the MAC address to the ble_app_hrs sample code
that was provided in the samples directory of the SDK.
Can you...
hi,
I am trying to develop a network of ble devices.i want nrf51822 to function as a master and slave( not necessarily simultaneous). For that i need to develop a custom...
