void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
szenario
beacon and receiving nodes are all MCU based and all powered by net, no local battery needed
the beacon usually located near the floor, the nodes will be located...
Blicky project runs and I can set break points and run through them - watching the LEDs blink appropriately. However, the HRS and Proximity projects will successfully load...
Hi all,
I'm using the LE1 to do the mutilceiver,if I donn't use the dynamic payload,I can do it successfully.However,if I use the dynamic payload to do Multiceiver,the...
Hi,
For the LE1,I found that 32.768kHz crystal oscillator need long time(about 350ms) to running,I must do some delay(about 350ms) for the software then use the RTC,or...
In moving to the "rev-2 51422 silicon, we find that the app_timer inevitably fails after minutes to several hours. Power requirement moves from about .002ma to 4.5ma then...
Hi,
I am planning to use an external DCDC to supply the NRF51822 in Low Voltage Mode.
In the datasheet a voltage range of 1.75-1.95 on VDD and VDD1.8 is mentioned. ...
Dear all
I'm testing for RF stability. As i used 24LU1(host) with 51822(device) be the platform. For audio data transmission. 8k 8bits data rate.
Timeslot set as 1008us...
Hi,
I don't have any problems running the bootloader with S110 7.0.0.-3.alpha on the PCA1001 but when using the same code (minus the led and button config of the PCA1001...
Hi,
I am having a hard time with the permanent storage.
I got it to work with updating a 24 bytes long struct in a persistant block of 32 bytes.
I noticed that the...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hello Gentlemen,
I'm looking for a good example on how to pair BLE sensor and Android using static passkey. I looked at ble_app_gls but I could not see how they set the...
I have the following code
// bondmngr code comes here for now
ble_bondmngr_init_t bondInitData;
bondInitData.flash_page_num_bond = FLASH_PAGE_BOND;
bondInitData.flash_page_num_sys_attr...
I want to save data sent by the Nordic UART/Serial Port Emulation over BLE to the phone.
Can the Nordic UART app save received UART data sent over BLE to the phone?
I've tried adding in the examples (heart rate by example) the:
sd_app_evt_wait();
(including #include "nrf_soc.h" and #include "nrf_sdm.h")
Disabling led, etc. And...
I am running into some symptoms here that I'm not understanding.
My peripheral is an nRF51822 using the S110 softdevice. It implements a service which sends out notifications...
