Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
In the release notes of the nRF51 SDK v8.0.0, section "Supported devices" it says that "This SDK is optimized for IC revision 3".
I am using a Laird BL600-SA-04 module...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Howdy, I'm trying to DFU my 51822 beacon v1.1.0 with MCP. MCP is failing the transfer. Steps I have taken are:
-Programmed my beacon with segger from the dk, both the SD...
There are apparently only 3 S120 examples available, and one of them is a peripheral example, which can be done with the S110, so really there are only two examples. This...
Hi,
I tried to run example: ble_app_multilink_central_s120_pca10028 but application goes to HardFault_Handler when it reaches sd_app_evt_wait() (in power_manage() function...
I have an I2C device that has an bidirectional interrupt pin.
This pin is pulled high externally with a weak pullup. When an event occurs on the device it pulls this pin...
Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
Hi,
i started writing a BLE application with the nRF51822 but i seam to have some trouble understanding BLE/S110. My application will consist of a button and an actor connected...
Hi there,
It states in the bill of materials for the QFAA RF PCB design of the nRF51822 that the 0402 model capactior is to be used. After using this capacitor package...
I'm using nRF51822-EK and running Keil compiler on XP within VirtualBox in a Linux Mint-14 host. I can't get the UART properly working through Segger J-LINK. It shows up all...
Hello Nordic Semi,
After being in production of a battery powered remote control for over a year now, we have found many batteries going flat in the field. I have been...
In my test, with the same configuration, ANTWARE II always searches much faster than nRF51422 software.
For example. I have Master channel and Slave channel set up at 4Hz...
The test code:
#include "nrf51.h"
int main(void) {
NRF_CLOCK->LFCLKSRC = 0UL; // Internal 32kHz RC
// Start the 32 kHz clock, and wait for the start up to complete...
