Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
I am working on a new design and i am using ST7789 (240 X 320 pixels) screen with nRF52840, it is working fine. I have followed the code provided in SDK example (big thanks...
Hi,
I´m trying to add a new, custom TX characteristic to Softdevice. I use example from SDK 16 "UART/Serial Port Emulation over BLE".
How I can do this, is explained...
Hi,
I flashed and run "ble_app_uart" example on nrf52833 DK. With an UART tool, I can recieve data from smartphone (rx characteristic) but I can´t send data from UART tool...
The sdk 16 - bootloader positions s140 softdevice V. 7.0.1 wrongly so that it is acknowledged as Application and does not work with nrf52840.
As you can see at the picture...
Is there a place to make suggestions for new releases of nRF5 SDK's or even contribute?
I've been using the current USBD CDC ACM library and needed to modify the app_usbd_cdc_acm...
Hi , I am making a zigbee application to write attribute on remote node. Please share the application structure to implement writing functionality of attribute on remote node...
Hi,
I am trying to test PSM settings on the nRF9160 using a custom PCB. I have set the active time to 3 minutes with a periodic TAU time of 10 minutes.
When the device...
I’m developing an application based on pc-ble-driver to talk to an nRF52840-based dongle (from Fanstel).
I’m having trouble disconnecting cleanly when a connection has operations...
Hi,
I´m using the NRF52810 device and have an issue with the SAADC peripheral.
I basically have 2 channel where i want to do some averaging to improve noise.
The setup...
Hi,
I was exploring TWI master with TWIS Slave example in SDK16.0.0.
It works for sequential reads in loop-back mode.
Now I connected the simulated eeprom slave...
hi, I set up the environment according to the nrf_sniffer_for_bluetooth_le_3.0.0_129d2b3 file downloaded from the official website of nordic, the operating environment is...
Dear Nordic Team,
we have unstable communication with an Osram BT device through nRF52840. We got information from Osram developers the nRF52840 is the right device for...
Hello!
I have question about Direction Finding in nRF52811, Angle-of-arrival to be exact.
To begin with, I have a custom board with nrf52811 onboard and 8 antennas....
Hi
As far as I know, NFC supports peer-to-peer communication, so I want to know whether peer-to-peer communication can be achieved between two 52832 through NFC? Is there...
