Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
I want to build my own board configuration:
The default configuration of the board is as follows: ncs?v1.2.0,zephyr?boards?arm?nrf9160_pca10090
How do I generate my own...
Hello
I'm using NRF connect the app to perform read and write on nrf52840 board SDK ver of 15.0.0.
I can perform the write and read operations using nrf connect app, and...
Hi
I'm working on a custom PCB based on nRF52840 soc and SDK version 16.0
currently I'm trying to interface my MCU with an external flash of model MT25QL01GBBB
my...
Hi,
I would like to interface ICM20948 with nrf52832 and communicate over TWI or SPI. That thing I don't understand is the logic voltage of the bus. In nrf52 specifications...
Hello,
I went through the instructions in the Getting Started Assistant to setup nRF Connect SDK for Linux but I am getting the following error when trying to build a project...
Hi,
I am programming nRF52840 dev kit (SDK16) as a peripheral with S140. Smartphone is central.
data needs to be transferred between both.
I need the dev kit to consume...
Hello, I’m using nRF52840 with SDK 16 and SD 7. My purpose is to save as much power is possible using high-frequency clock (32MHz) only during periodic duties and BLE activity...
What are best practices for updating an nRF52832 via UART from an nRF52840? There seem to be at least two problems to solve:
Transmitting the 832 image via BLE to the...
Hello,
I'm measuring the idle current using a PCA10040 DK, SDK v16.
Finding that the idle current is about 3uA (which I think is correct) after any debug operation like...
Our setup is using a NRF52832 with SDK15.0.0.
While working with a time sensitive external circuit where we both sample the state of the GPIO and enable LDETECT on it...
I have just received my nRF52 development board and I have tried to program one of the pre-bjui;t examples (Blinky). The USB drive on the board appears and if I drag the hex...
Hi,
I'm using an application with FreeRTOS , nRF52833, SDK 16.
When I'm trying to get it into low power (sleep mode) the system still consumes ~4mA
In vPortSuppressTicksAndSleep...
Hi,
I am starting with PPK. Tried some measurements on ble examples and looks like i am doing something wrong. I have aproximatelly 7mA during advertising. Am I doing something...
Hi,
i have load existing program to new nRF52 module. But it shows NRF_ERROR_NO_MEM.
Same old module doesn't show this error. i also reload the soft device. But no improvement...
I'm looking to implement the following security schema:
The peripheral does not have a display nor input capabilities
A smartphone will connect to the device
The peripheral...
