I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi guys.
I'm trying to merge two projects ble_app_beacon and nrf_crypto_aes_cbc_with_padding.
I used nrf_crypto_aes_cbc_with_padding as base, copied it to another folder...
hi
i want to develop a keyboard that can communicate whith pc by ble and 2.4g . now,the 2.4g's communicate between nrf52840 and nrf24lu1p is achieved by project gzp_desktop_emulator...
I am based in Hong Kong. I purchased NB-IoT sim card with "Three".
When using LTE Link Monitor, (with at_client) I can connect to the NB_IoT network, as Three support told...
Hi! I would like to power the DK through a external power bank. This leads to led5 blinking rapidly for a while and then turning off. I assume this is because of the debugger...
Hi Team,
We are trying to compile the code with my changes, that changes are normal changes only.
But we are getting below errors in "nrf52840.h" . But we didn't do...
I have a nrf51-DK, SDK 9.0, S110, dual-bank bootloader that supports both serial and ble protocols, developed using GCC/Eclipse. I'm able to flash my app/bootloader/softdevice...
We are building a sollution using nRF52832. Using the UART over BLE application example as a base we managed to add DFU capabilities to the application etc.
Right now I...
Dear NRF community and support This is a followup question to the DevZone post https://devzone.nordicsemi.com/f/nordic-q-a/2860/flashing-bootloader-and-application-via-j-link...
From everything I know and understand of the system architecture, this shouldn't be possible, but one of our early production units out in the fields has twice now apparently...
I'm designing a two-part computer input device: Part A will communicate with the computer over BLE, but it must also be able to forward along messages from Part B. Here's...
Hi,
I am trying to update the MTU between the central and peripheral to the maximum MTU.
at the connection interrupt from the central side I added
but I got error...
For nRF52832 I see in the datasheet:
I OFF_RAMOFF_GPIO System OFF, No RAM retention, Wake on GPIO,
While for nRF52840 only “System OFF, no RAM retention, wake on reset...
I have an iOS App which is just designed for updating our device firmware OTA. It uses the Nordic DFU library, updated to the latest cocoapod. It connects to our device, and...
Hi,
I use OpenWRT and nRF52832 to develop a BLE gateway, the nRF52832 connected to OenWRT through UART. Now,we need the uart serial DFU of nRF52832, and I found that nrfutil...
