Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
I'm upgrading a project from SDK 15 to SDK 16. Previously in my gap parameters init I had this code
This works fine for seeing the peripheral and operating it as a UART...
I wasn't sure which product to put in. I am looking for a BLE discovery tool for EEG devices -- particularly the Muse 2 Headband. Which of Nordic's software should I use for...
Hi,
In our project, we are using a small RTOS to switch between simple tasks and set MPU. We would like to run all task in unprivileged mode, but some Nordic SDK libraries...
Hi everyone,
I have written a code that sends data over BLE notifications (IMU data). It works great so far and now I want to read the analog values from eight force sensors...
Hi everyone,
I have a problem I can't sort out. My program runs fine indefinitely if I set one variable in a function at one point but if I don't do that, the program, or...
Hello,
We have around 700 product in the field based on the Simblee BLE module, which was discontinued 1+ year ago. Application was developed using Simblee's proprietary...
Hello,
I need to develop two applications for nRF51822 using SES version 4.18 (macOS). One is a DFU bootloader. The other is an application based on the ble_app_uart (ble_peripheral...
Hello,
I am trying to run the BLE Thread Dynamic Template example on a nRF52840 dongle. I'm using Segger Embedded Studio to generate an hex file. I flash the hex file to...
Hello,
During testing we found that whenever in system off mode, the CPU wakes from VBUS rising. As expected. We then do a vibration to notify the user the USB cable was...
When integrating nRF Mesh SDK 4.1 with nRF SDK 16 I got an error in runtime.
The call sequence:
mesh_init() -> mesh_stack_init() -> nrf_mesh_init() -> mesh_config_init...
Hi all,
I have really strange behavior with Sesgger SES. I'm working on Linux Kubuntu lastest version.
Segger version is :
SEGGER Embedded Studio for ARM
Release 4...
I am trying to use C++ with an nRF5 board, but I'm running into issues with the MDK, IAR (v8.40.2), and C++. When I try to include "nrfx_gpiote.h" in a .cpp file, I get the...
Hi,
I have a basic setup consisting of a time-slotted transmitter and receiver so that I can experiment with the raw coded and uncoded modes, exploring all the NRF_RADIO...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hi, I want to create a mesh network with two nrf52840 dongles. To programming them I used the light-switch example from SDK Mesh v4.0.0 following the steps in this tutorial...
